- 您現在的位置：買賣IC網 > PDF目錄98281 > TPS40022PWPR (TEXAS INSTRUMENTS INC) 0.01 A SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO16 PDF資料下載
參數資料
| 型號： | TPS40022PWPR |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 穩壓器 |
| 英文描述： | 0.01 A SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO16 |
| 封裝： | POWERPAD, PLASTIC, HTSSOP-16 |
| 文件頁數： | 8/29頁 |
| 文件大小： | 337K |
| 代理商： | TPS40022PWPR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁
TPS40020
TPS40021
TPS40022
SLUS535 – MARCH 2003
www.ti.com
16
REFERENCE DESIGN
This design used the TPS40020 PWM controller to facilitate a step-down application from 3.3-V to 1.5 V. (see
Figure 6) Design specifications include:
D Input voltage: 2.5 V ≤ VIN ≤ 5.0 V
D Nominal voltage: 3.3 V
D Output voltage VOUT: 1.5 V
D Output current IOUT: 20 A
D Switching frequency: 300 kHz
DESIGN PROCEDURE
Setting the Frequency
Choosing the optimum switching frequency is complicated. The higher the frequency, the smaller the
inductance and capacitance needed, so the smaller the size, but then the the switching losses are higher, the
efficiency is poorer. For this evaluation module, 300 kHz is chosen for reasonable efficiency and size.
A resistor R4, which is connected from pin 7 to ground, programs the oscillator frequency. The approximate
operating frequency is calculated in equation (3)
f
OSC (MHz) +
35.4
R4 (k
W) [
118 k
W
Therefore, a 118-k
resistor is chosen for 300 kHz operation.
Inductance Value
The inductance value can be calculated by equation (2).
L
(min) +
V
OUT
f
I
RIPPLE
1
*
V
OUT
V
IN(max)
where IRIPPLE is the ripple current flowing through the inductor, which affects the output voltage ripple and core
losses.
Based on 20% ripple current and 300 kHz, the inductance value is calculated to 0.76
H and a 0.75-H inductor
(part number is CDEP149–0R7) is chosen. The ESR of this inductor is 1.1 m
and the loss is 440 mW, which
is approximately 1.5% of output power.
C
OUT(min) +
I
RIPPLE
8
f
V
RIPPLE
ESR
OUT +
V
RIPPLE
I
RIPPLE
With 1% output voltage ripple, the needed capacitance is at least 114
F and its ESR should be less than 3.7
m
. Three 2-V, 470-F, POSCAP capacitors from Sanyo are used. The ESR is 10 m each.
The required input capacitance is calculated in equation (5). The calculated value is approximately 348
F.
Three 6.0-V, 330-
F POSCAP capacitors with 10 m ESR are used to handle 10 A of RMS input current.
Additionally, two ceramic capacitors are used to reduce the switching ripple current.
C
IN(min) + IOUT(max)
D
(max)
T
S
V
RIPPLE
(3)
(4)
(5)
(6)
(7)
相關PDF資料 |
PDF描述 |
|---|---|
| TPS40042DRCTG4 | SWITCHING CONTROLLER, 700 kHz SWITCHING FREQ-MAX, PDSO10 |
| TPS40055MPWPREPG4 | SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO16 |
| TPS40055QPWPRQ1 | SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO16 |
| TPS40054QPWPRQ1 | SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO16 |
| TPS40070PWPRG4 | 2 A SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO16 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPS40040 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:LOW PIN COUNT, LOW VIN (2.5 V TO 5.5 V) SYNCHRONOUS BUCK DC-TO-DC CONTROLLER WITH ENABLE |
| TPS40040DRBR | 功能描述:DC/DC 開關控制器 Lo Vin Synch Buck DC/DC Cntrlr RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| TPS40040DRBRG4 | 功能描述:DC/DC 開關控制器 Lo Vin Synch Buck DC/DC Cntrlr RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| TPS40040DRBT | 功能描述:DC/DC 開關控制器 Low Vin Synch Buck DC/DC Controller RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| TPS40040DRBT | 制造商:Texas Instruments 功能描述:Peak Reflow Compatible (260 C):Yes |
發布緊急采購，3分鐘左右您將得到回復。