- 您現在的位置：買賣IC網 > PDF目錄98281 > TPS40075RHLR (TEXAS INSTRUMENTS INC) 2 A SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PQCC20 PDF資料下載
參數資料
| 型號： | TPS40075RHLR |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 穩壓器 |
| 英文描述： | 2 A SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PQCC20 |
| 封裝： | PLASTIC, QFN-20 |
| 文件頁數： | 19/44頁 |
| 文件大小： | 806K |
| 代理商： | TPS40075RHLR |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁
www.ti.com
I
CAP(RMS) +
I
LOAD(max) * IIN(avg)
2
) D
I2
12
D ) IIN(avg)
2
(1 * D)
(23)
I
D +
V
O
V
IN(min)
I
LOAD(max)
2
) D
I2
12
(24)
SLUS676A – MAY 2006 – REVISED SEPTEMBER 2007
3.1.3. Input Capacitor, CIN, ELCO and MLCC
The input capacitor is selected to handle the ripple current of the buck stage. Also a relative large capacitance is
used to keep the ripple voltage on the supply line low. This is especially important where the supply line is high
impedance. It is recommended that the supply line be kept low impedance. The input capacitor ripple current can
be calculated using Equation 23.
where
I
IN(avg) is the average input current
This is calculated simply by multiplying the output DC current by the duty cycle. The ripple current in the input
capacitor is 5.05 A. A 1206 MLCC using X7R material has a typical dissipation factor of 5%. For a 2.2
μF
capacitor at 400 kHz the ESR is approximately 7.2 m
. If two capacitors are used in parallel the power
dissipation in each capacitor is less than 46 mW.
A 470
μF/16 V electrolytic capacitor is added to maintain the voltage on the input rail.
3.1.4 Switching MOSFET, QSW
The following key parameters must be met by the selected MOSFET.
Drain source voltage, V
DS, must be able to withstand the input voltage plus spikes that may be on the
switching node. For this design a VDS rating of 25 V to 30 V is recommended.
Drain current, I
be greater than 5 A.
Gate source voltage, V
GS must be able to withstand the gate voltage from the control device . For the
TPS40075 this is 9 V.
Once the above boundary parameters are defined the next step in selecting the switching MOSFET is to select
the key performance parameters. Efficiency is the performance characteristic which drives the other selection
criteria. Target efficiency for this design is 90%. Based on 1.5-V output and 15 A this equates to a power loss in
the converter of 2.5 W. Using this figure a target of 0.5 W dissipated in the switching MOSFET was chosen.
26
Copyright 2006–2007, Texas Instruments Incorporated
Product Folder Link(s) :TPS40075
相關PDF資料 |
PDF描述 |
|---|---|
| TPS40075RHLTG4 | 2 A SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PQCC20 |
| TPS40077PWPR | 2 A SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO16 |
| TPS40077PWPRG4 | 2 A SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO16 |
| TPS40077PWPG4 | 2 A SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO16 |
| TPS40090QPWRQ1 | SWITCHING CONTROLLER, 1200 kHz SWITCHING FREQ-MAX, PDSO24 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPS40075RHLRG4 | 功能描述:DC/DC 開關控制器 Wide Input Synch Buck Controller RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| TPS40075RHLT | 功能描述:DC/DC 開關控制器 Wide Input Synch Buck Controller RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| TPS40075RHLTG4 | 功能描述:DC/DC 開關控制器 Wide Input Synch Buck Controller RoHS:否 制造商:Texas Instruments 輸入電壓:6 V to 100 V 開關頻率: 輸出電壓:1.215 V to 80 V 輸出電流:3.5 A 輸出端數量:1 最大工作溫度:+ 125 C 安裝風格: 封裝 / 箱體:CPAK |
| TPS40077 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:HIGH-EFFICIENCY, MIDRANGE-INPUT, SYNCHRONOUS BUCK CONTROLLER WITH VOLTAGE FEED-FORWARD |
| TPS40077_07 | 制造商:TI 制造商全稱:Texas Instruments 功能描述:HIGH-EFFICIENCY, MIDRANGE-INPUT, SYNCHRONOUS BUCK CONTROLLER WITH VOLTAGE FEED-FORWARD |
發布緊急采購，3分鐘左右您將得到回復。