- 您現在的位置：買賣IC網 > PDF目錄98283 > TPS57114QRTERQ1 (TEXAS INSTRUMENTS INC) SWITCHING REGULATOR, 2000 kHz SWITCHING FREQ-MAX, PQCC16 PDF資料下載
參數資料
| 型號： | TPS57114QRTERQ1 |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 穩壓器 |
| 英文描述： | SWITCHING REGULATOR, 2000 kHz SWITCHING FREQ-MAX, PQCC16 |
| 封裝： | 3 X 3 MM, GREEN, PLASTIC, WQFN-16 |
| 文件頁數： | 4/37頁 |
| 文件大小： | 1309K |
| 代理商： | TPS57114QRTERQ1 |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁
O
0.799 V
R2 = R1
V
0.799 V
÷
-
è
SLVSAH5A
– DECEMBER 2010 – REVISED MARCH 2011
DETAILED DESCRIPTION
FIXED FREQUENCY PWM CONTROL
The TPS57114 -Q1 uses an adjustable fixed frequency, peak current mode control. The output voltage is
compared through external resistors on the VSENSE pin to an internal voltage reference by an error amplifier
which drives the COMP pin. An internal oscillator initiates the turn on of the high side power switch. The error
amplifier output is compared to the high side power switch current. When the power switch current reaches the
COMP voltage level the high side power switch is turned off and the low side power switch is turned on. The
COMP pin voltage increases and decreases as the output current increases and decreases. The device
implements a current limit by clamping the COMP pin voltage to a maximum level and also implements a
minimum clamp for improved transient response performance.
SLOPE COMPENSATION AND OUTPUT CURRENT
The TPS57114 -Q1 adds a compensating ramp to the switch current signal. This slope compensation prevents
sub-harmonic oscillations as duty cycle increases. The available peak inductor current remains constant over the
full duty cycle range.
BOOTSTRAP VOLTAGE (BOOT) AND LOW DROPOUT OPERATION
The TPS57114 -Q1 has an integrated boot regulator and requires a small ceramic capacitor between the BOOT
and PH pin to provide the gate drive voltage for the high side MOSFET. The value of the ceramic capacitor
should be 0.1
μF. A ceramic capacitor with an X7R or X5R grade dielectric with a voltage rating of 10 V or higher
is recommended because of the stable characteristics over temperature and voltage.
To improve drop out, the TPS57114 -Q1 is designed to operate at 100% duty cycle as long as the BOOT to PH
pin voltage is greater than 2.2 V. The high side MOSFET is turned off using an UVLO circuit, allowing for the low
side MOSFET to conduct when the voltage from BOOT to PH drops below 2.2 V. Since the supply current
sourced from the BOOT pin is low, the high side MOSFET can remain on for more switching cycles than are
required to refresh the capacitor, thus the effective duty cycle of the switching regulator is high.
ERROR AMPLIFIER
The TPS57114 -Q1 has a transconductance amplifier. The error amplifier compares the VSENSE voltage to the
lower of the SS/TR pin voltage or the internal 0.800 V voltage reference. The transconductance of the error
amplifier is 245
μA/V during normal operation. When the voltage of VSENSE pin is below 0.800 V and the device
is regulating using the SS/TR voltage, the gm is typically greater than 79
μA/V, but less than 245 μA/V. The
frequency compensation components are placed between the COMP pin and ground.
VOLTAGE REFERENCE
The voltage reference system produces a precise
±1% voltage reference over temperature by scaling the output
of a temperature-stable bandgap circuit. The bandgap and scaling circuits produce 0.800 V at the non-inverting
input of the error amplifier.
ADJUSTING THE OUTPUT VOLTAGE
The output voltage is set with a resistor divider from the output node to the VSENSE pin. It is recommended to
use divider resistors with 1% tolerance or better. Start with a 100 k
for the R1 resistor and use the Equation 1
to calculate R2. To improve efficiency at light loads consider using larger value resistors. If the values are too
high the regulator is more susceptible to noise and voltage errors from the VSENSE input current are noticeable.
vertical spacer
(1)
12
Copyright
2010–2011, Texas Instruments Incorporated
Product Folder Link(s): TPS57114 -Q1
相關PDF資料 |
PDF描述 |
|---|---|
| TPS60100PWP | 0.2 A SWITCHED CAPACITOR REGULATOR, 400 kHz SWITCHING FREQ-MAX, PDSO20 |
| TPS60101PWPG4 | SWITCHED CAPACITOR REGULATOR, 400 kHz SWITCHING FREQ-MAX, PDSO20 |
| TPS60101PWPRG4 | 0.1 A SWITCHED CAPACITOR REGULATOR, 400 kHz SWITCHING FREQ-MAX, PDSO20 |
| TPS60230RGTTG4 | 0.2 A SWITCHED CAPACITOR REGULATOR, 1250 kHz SWITCHING FREQ-MAX, PQCC16 |
| TPS60230RGTT | 0.2 A SWITCHED CAPACITOR REGULATOR, 1250 kHz SWITCHING FREQ-MAX, PQCC16 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPS57140MDRCREP | 功能描述:Buck Switching Regulator IC Positive Adjustable 0.8V 1 Output 1.5A 10-VFDFN Exposed Pad 制造商:texas instruments 系列:SWIFT?? 包裝:剪切帶（CT） 零件狀態:有效 功能:降壓 輸出配置:正 拓撲:降壓 輸出類型:可調式 輸出數:1 電壓 - 輸入（最小值）:3.5V 電壓 - 輸入（最大值）:42V 電壓 - 輸出（最小值/固定）:0.8V 電壓 - 輸出（最大值）:39V 電流 - 輸出:1.5A 頻率 - 開關:100kHz ~ 2.5MHz 同步整流器:無 工作溫度:-55°C ~ 125°C（TA） 安裝類型:表面貼裝 封裝/外殼:10-VFDFN 裸露焊盤 供應商器件封裝:10-VSON（3x3） 標準包裝:1 |
| TPS57140QDGQRQ1 | 功能描述:直流/直流開關轉換器 3.5-42Vin,1.5A Step Down Cnvrtr RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| TPS57140QDRCRQ1 | 功能描述:直流/直流開關轉換器 3.5-42Vin,1.5A Step Down Cnvrtr RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
| TPS57160-Q1EVM | 功能描述:EVAL MODULE FOR TPS57160-Q1 制造商:texas instruments 系列:SWIFT??，Eco-Mode?? 零件狀態:在售 主要用途:DC/DC，步降 輸出和類型:1，非隔離 電壓 - 輸出:5V 電流 - 輸出:1A 電壓 - 輸入:9 V ~ 16 V 穩壓器拓撲:降壓 頻率 - 開關:2MHz 板類型:完全填充 所含物品:板 使用的 IC/零件:TPS57160-Q1 標準包裝:1 |
| TPS57160QDGQRQ1 | 功能描述:直流/直流開關轉換器 3.5-60V,1.5A Step Down SWIFT Converter RoHS:否 制造商:STMicroelectronics 最大輸入電壓:4.5 V 開關頻率:1.5 MHz 輸出電壓:4.6 V 輸出電流:250 mA 輸出端數量:2 最大工作溫度:+ 85 C 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。