- 您現在的位置：買賣IC網 > PDF目錄98286 > TPS65810RTQT (TEXAS INSTRUMENTS INC) 9-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC56 PDF資料下載
參數資料
| 型號： | TPS65810RTQT |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 電源管理 |
| 英文描述： | 9-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC56 |
| 封裝： | 8 X 8 MM, GREEN, PLASTIC, QFN-56 |
| 文件頁數： | 32/99頁 |
| 文件大小： | 2128K |
| 代理商： | TPS65810RTQT |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁當前第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁
www.ti.com
TPS65810 OPERATING MODE CONTROLS
SEQUENCING AND OPERATING MODES – I
2C REGISTERS
SLVS658B – MARCH 2006 – REVISED FEBRUARY 2007
3. ) If sleep was set by a system low voltage detection, power good fault or SLEEP_MODE, with battery and
input power present: all external input supplies connected to AC and USB pins must be removed, and then at
least one of them reconnected to the system. The input power cycling triggers a transition from SLEEP mode
to the ENABLE mode.
PROCESSOR STANDBY STATE – This state is set using an I2C register or a GPIO configured as SM1/SM2
standby control. In standby mode operation, the SM1 and SM2 voltages are set to value distinct than the normal
mode output voltage, and SM1/SM2 are set to PFM mode. The standby output voltage is defined in I2C registers
SM1_STANDBY and SM2_STANDBY.
HARDWARE RESET: A dedicated control pin, HOT_RESET, enables implementation of a hardware reset
function. The system reset pin RESPWRON is set to LO when HOT_RESET = LO for a period longer than the
internal deglitch (5mSec typ). The RESET mode is started when the HOT_RESET pin transitions from LO to HI,
as shown in the state diagram. When HOT_RESET = LO all I2C registers are reset to the default power-up
values.
SOFTWARE RESET: The external host can set the TPS65810 in RESET mode using the I2C register
SOFT_RESET, bit B0 (SOFT_RST).
SOFTWARE SLEEP: The external host can set the TPS65810 in SLEEP mode using the I2C register
SOFT_RESET, bit B6 (SLEEP_MODE).
A software reset does not affect the contents of the I2C registers.
The I2C registers that control sequencing-related functions are shown below. The HEX address for each register
is shown by the register name, together with the R or W functionality for the register bits. Shaded values indicate
default initial power-up values.
SOFT_RESET, ADDRESS=08, ALL BITS R/W, BITS B7/B6/B1/B0 APPLY TO SEQUENCING.
B7
B6
B5
B4
B3
B2
B1
B0
Bit name
STBY MODE
SLEEP MODE
NOT USED
SM3_LF_OSc
NOT USED
nRAMLOAD
SOFT RST
Function
SET SM1 AND
SET TPS65810
NOT USED
NOT RELATED
NOT USED
RAM RESET
SOFTWARE
SM2 IN
IN SLEEP
TO
FLAG
RESET
STANDBY
MODE
SEQUENCING
CONTROL
MODE
SEE SM3
SECTION
When 0
NOT ACTIVE
NOT USED
RAM
NOT ACTIVE
DEFAULTS
LOADED
When 1
When 1 SET
SET SLEEP
NOT USED
RAM
SET RESET
SM1 AND SM2
MODE (reset to
DEFAULTS
MODE (reset to
IN STANDBY
LO internally)
NOT LOADED
LO internally)
Some host algorithms need to identify when the power-up defaults are loaded in the RAM, in order to start
routines that initialize specific RAM registers. If that functionality is required the nRAMLOAD bit should be set to
HI by the host when entering the NORMAL operation mode. The nRAMLOAD bit is reset to LO by the TPS65810
when the power-up defaults are loaded in the I2C registers (V(OUT) < VUVLO OR V(HOT_RESET) = LO),
enabling the host algorithm to detect that the RAM registers need to be initialized.
The integrated supplies status is available in a dedicated register, shown below. The host can select which
integrated supply outputs trigger a power-good fault condition using the PGOODFAULT_MASK register. When a
non-masked power-good status register bit toggles state, the sequence controller generates a transition in the
TPS65810 state machine, indicated as a PGOOD FAULT in TPS65810 state diagram. The power-good status
register and mask register are shown below:
SYSTEM STATUS MONITORED BY SEQUENCING CONTROLLER
B7
B6
B5
B4
B3
B2
B1
B0
PGOOD, ADDRESS=02, ALL BITS READ ONLY - POWER UP DEFAULTS SHOW SYSTEM STATUS WHEN EXITING POWER DOWN
Bit name
PGOOD SM1
PGOOD SM2
PGOOD SM3
PGOOD LDO1
PGOOD LDO2
PGOOD LDO3
PGOOD LDO4
PGOOD LDO5
Function
SM1 OUTPUT
SM2
SM3 OVP
LDO1 OUTPUT
LDO2 OUTPUT
LDO3 OUTPUT
LDO4 OUTPUT
LDO5 OUTPUT
STATUS
OUTPUT
STATUS
38
Copyright 2006–2007, Texas Instruments Incorporated
相關PDF資料 |
PDF描述 |
|---|---|
| TPS65820RSHTG4 | 8-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC56 |
| TPS65910RSLT | POWER SUPPLY SUPPORT CKT, PQCC48 |
| TPS65920A2ZCHR | SPECIALTY CONSUMER CIRCUIT, PBGA139 |
| TPS65920A2ZCH | SPECIALTY CONSUMER CIRCUIT, PBGA139 |
| TPS65920BZCHR | SPECIALTY CONSUMER CIRCUIT, PBGA139 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPS65810RTQTG4 | 功能描述:電池管理 Int Sgl-Cell Lit-Ion Batt & Pwr Mgmt IC RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| TPS65811RTQR | 功能描述:電池管理 Integr S-C Li-Ion RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| TPS65811RTQRG4 | 功能描述:電池管理 Integr S-C Li-Ion RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| TPS65811RTQT | 功能描述:電池管理 Integr S-C Li-Ion RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| TPS65811RTQTG4 | 功能描述:電池管理 Integr S-C Li-Ion RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。