- 您現在的位置：買賣IC網 > PDF目錄98286 > TPS65810RTQT (TEXAS INSTRUMENTS INC) 9-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC56 PDF資料下載
參數資料
| 型號： | TPS65810RTQT |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 電源管理 |
| 英文描述： | 9-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC56 |
| 封裝： | 8 X 8 MM, GREEN, PLASTIC, QFN-56 |
| 文件頁數： | 76/99頁 |
| 文件大小： | 2128K |
| 代理商： | TPS65810RTQT |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁當前第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁
www.ti.com
SM3CONVERTER
>50%DUTY CYCLE
REPETITIONPERIOD
SM3CONVERTER
50%DUTY CYCLE
SM3CONVERTER
<50%DUTY CYCLE
SM3 Control Logic Overview
Peak Current Control (Boost Converter)
I
P(typ) + IMAX(L3) )
V(OUT)
L
100 ns, or : I
P(typ) + 500 mA )
V(OUT)
L
100 ns
(8)
Soft Start
SLVS658B – MARCH 2006 – REVISED FEBRUARY 2007
Figure 54. Example of Distinct Duty Cycles
The repetition period can be set using the register SOFT_RESET control bit SM3_LF_OSC to either 183 Hz (HI)
or 122 Hz (LO). Each repetition period has a total of 256 pulses, enabling a resolution of 0.4% when
programming the duty cycle.
The SM3 boost converter operates in a pulse frequency modulation (PFM) scheme with constant peak current
control. This control scheme maintains high efficiency over the entire load current range and enables the use of
small external components, as the switching frequency can reach up to 1 MHz depending on the load conditions.
The LED current ripple is defined by the external inductor size.
The converter monitors the sense voltage at pin FB3, and turns on the integrated power stage switch when V(FB3)
is below the 250-mV (typ) internal reference voltage and the LED Switch is ON, starting a new cycle. The
integrated power switch turns off when the inductor current reaches the internal 500-mA (typ) peak current limit,
or if the switch is on for a period longer than the maximum on-time of 6
s (typ). The integrated power switch
also turns off when the LED switch is set to OFF. As the integrated power switch is turned off, the external
Schottky diode is forward biased, delivering the stored inductor energy to the output. The main switch remains off
until the FB3 pin voltage is below the internal 250-mV reference voltage and the LED switch is turned ON, when
it is turned on again.
This PFM peak current control scheme sets the converter in discontinuous conduction mode (DCM), and the
switching frequency depends on the inductor, input/output voltage and LED current. Lower LED currents reduce
the switching frequency, with high efficiency over the entire LED current range. This regulation scheme is
inherently stable, allowing a wide range for the selection of the inductor and output capacitor.
The SM3 integrated power stage switch is turned on until the inductor current reaches the dc current limit IMAX(L3)
(500 mA, typ). Due to internal delays, typically around 100 ns, the actual current exceeds the DC current limit
threshold by a small amount. The typical peak current limit can be calculated as shown in Equation 8
The current overshoot is directly proportional to the input voltage, and inversely proportional to the inductor
value.
All inductive step-up converters exhibit high in-rush current during start-up. If no special precautions are taken,
voltage drops can be observed at the input supply rail during start-up, with unpredictable results in the overall
system operation.
The SM3 boost converter limits the inrush current during start-up by increasing the current limit in three steps:
1. 125 mA (typ),
2. 250 mA (typ) and
3. 500 mA (typ)
The two initial steps (125 mA and 250 mA) are active for 256 power stage switching cycles.
78
Copyright 2006–2007, Texas Instruments Incorporated
相關PDF資料 |
PDF描述 |
|---|---|
| TPS65820RSHTG4 | 8-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC56 |
| TPS65910RSLT | POWER SUPPLY SUPPORT CKT, PQCC48 |
| TPS65920A2ZCHR | SPECIALTY CONSUMER CIRCUIT, PBGA139 |
| TPS65920A2ZCH | SPECIALTY CONSUMER CIRCUIT, PBGA139 |
| TPS65920BZCHR | SPECIALTY CONSUMER CIRCUIT, PBGA139 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPS65810RTQTG4 | 功能描述:電池管理 Int Sgl-Cell Lit-Ion Batt & Pwr Mgmt IC RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| TPS65811RTQR | 功能描述:電池管理 Integr S-C Li-Ion RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| TPS65811RTQRG4 | 功能描述:電池管理 Integr S-C Li-Ion RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| TPS65811RTQT | 功能描述:電池管理 Integr S-C Li-Ion RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| TPS65811RTQTG4 | 功能描述:電池管理 Integr S-C Li-Ion RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。