- 您現在的位置：買賣IC網 > PDF目錄98286 > TPS65810RTQT (TEXAS INSTRUMENTS INC) 9-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC56 PDF資料下載
參數資料
| 型號： | TPS65810RTQT |
| 廠商： | TEXAS INSTRUMENTS INC |
| 元件分類： | 電源管理 |
| 英文描述： | 9-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC56 |
| 封裝： | 8 X 8 MM, GREEN, PLASTIC, QFN-56 |
| 文件頁數： | 85/99頁 |
| 文件大小： | 2128K |
| 代理商： | TPS65810RTQT |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁當前第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁
www.ti.com
General Purpose I/Os — GPIO 1, 2, 3
GPIOs Input Level Configuration
S1
S2
D
C
ENB
Multiplexer
Q
SET
CLR
D
GPIO
SignalPin
HI=RisingEdge,
LO=FallingEdge
UVLO
GPIOConfig= OUTPUT
Equivalentcircuitforinternal
logicwhenconfiguredasedge
interruptwithnomasking
I CINTACKREAD
C
2
ommand?
INT
SLVS658B – MARCH 2006 – REVISED FEBRUARY 2007
The TPS65810 integrates 3 general purpose open drain ports (GPIOs) that can be configured as selectable
inputs or outputs. When configured as outputs the output level can be set to LO or HI via I2C commands. When
the GPIOs are configured as inputs the action to be taken when a transition or HI/LO level is detected at the
GPIO pin is selectable via I2C.
When configured as inputs the GPIOs can be set in the following modes:
1. Interrupt request: In this mode of operation, a transition at the GPIO pin generates an interrupt request at the
interrupt controller. The GPIO interrupt request can be masked at the INT_MASK register. This operation
mode is available for GPIO’s 1 and 2.
2. SM1 and SM2 control: The GPIO’s can be used to turn the converters SM1 and SM2 ON/OFF, as well as
setting them in standby mode. This control mode is available for GPIO1 (SM1 on/off and SM1/SM2 standby)
and GPIO2 (SM2 on/off control).
3. ADC trigger: GPIO3 can be configured as an external ADC trigger. The GPIO3 trigger configuration bit is
located at the ADC register ADC_DELAY.
When using I2C commands, the GPIO1 and GPIO2 pins can be configured as logic output signals or as
level-controlled inputs which enables (or disables) the switch mode converters SM1 and/or SM2. These pins may
also be configured as rising- or falling-edge-triggered inputs to externally control the generation of an interrupt
signal (INT), if desired.
The GPIO3 pin may be used as an external trigger source to start an A/D conversion cycle or as a logic output.
See Figure 58 for a description of the logic used for GPIO1 and GPIO2 inputs when configured for
edge-triggered interrupt generation. The signal from the GPIO pin input is double-latched before being sent to the
interrupt contoller logic. The inversion of the Q output from the first flip-flop must be HI to allow the output latch to
be cleared when a READ command occurs. On the initial edge of the GPIO signal, the Q output of the flip-flop is
set (HI). The INT line is asserted (LO) after the initial selected edge from the GPIO pin. On the next falling (or
rising) edge of the GPIO pin, the interrupt can again be cleared (which allows the INT pin to go back high). The
INT signal is cleared (set back HI) after an I2C READ operation is performed.
Thus, two successive edges of the GPIO signal, followed by an I2C READ command, are required to clear the
INT pin output. If no I2C READ commands occur, repeatedly applying edges to the GPIO pin does not toggle the
state of the INT pin output.
In addition to an I2C READ command after two GPIO edges, a UVLO event or reconfiguration of the GPIO pins
as outputs also de-asserts the INT signal.
Figure 58. GPIO 1 or GPIO2 Configured as an Interrupt Request Input
86
Copyright 2006–2007, Texas Instruments Incorporated
相關PDF資料 |
PDF描述 |
|---|---|
| TPS65820RSHTG4 | 8-CHANNEL POWER SUPPLY SUPPORT CKT, PQCC56 |
| TPS65910RSLT | POWER SUPPLY SUPPORT CKT, PQCC48 |
| TPS65920A2ZCHR | SPECIALTY CONSUMER CIRCUIT, PBGA139 |
| TPS65920A2ZCH | SPECIALTY CONSUMER CIRCUIT, PBGA139 |
| TPS65920BZCHR | SPECIALTY CONSUMER CIRCUIT, PBGA139 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TPS65810RTQTG4 | 功能描述:電池管理 Int Sgl-Cell Lit-Ion Batt & Pwr Mgmt IC RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| TPS65811RTQR | 功能描述:電池管理 Integr S-C Li-Ion RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| TPS65811RTQRG4 | 功能描述:電池管理 Integr S-C Li-Ion RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| TPS65811RTQT | 功能描述:電池管理 Integr S-C Li-Ion RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
| TPS65811RTQTG4 | 功能描述:電池管理 Integr S-C Li-Ion RoHS:否 制造商:Texas Instruments 電池類型:Li-Ion 輸出電壓:5 V 輸出電流:4.5 A 工作電源電壓:3.9 V to 17 V 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 封裝 / 箱體:VQFN-24 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。