- 您現在的位置：買賣IC網 > PDF目錄365982 > TSM5518M (NXP Semiconductors N.V.) 1.3 GHz Bidirectional IIC-bus controlled synthesizer(1.3 GHz雙向IIC總線控制的合成器) PDF資料下載
參數資料
| 型號： | TSM5518M |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | 1.3 GHz Bidirectional IIC-bus controlled synthesizer(1.3 GHz雙向IIC總線控制的合成器) |
| 中文描述： | 1.3 GHz的雙向國際進口控制合成巴士（1.3千兆赫雙向進口證總線控制的合成器） |
| 文件頁數： | 15/20頁 |
| 文件大小： | 161K |
| 代理商： | TSM5518M |
1997 Mar 07
15
Philips Semiconductors
Product specification
1.3 GHz bidirectional I
2
C-bus controlled
synthesizer
TSA5518M
SOLDERING
Introduction
There is no soldering method that is ideal for all IC
packages. Wave soldering is often preferred when
through-hole and surface mounted components are mixed
on one printed-circuit board. However, wave soldering is
not always suitable for surface mounted ICs, or for
printed-circuits with high population densities. In these
situations reflow soldering is often used.
This text gives a very brief insight to a complex technology.
A more in-depth account of soldering ICs can be found in
our “IC Package Databook”(order code 9398 652 90011).
Reflow soldering
Reflow soldering techniques are suitable for all SSOP
packages.
Reflow soldering requires solder paste (a suspension of
fine solder particles, flux and binding agent) to be applied
to the printed-circuit board by screen printing, stencilling or
pressure-syringe dispensing before package placement.
Several techniques exist for reflowing; for example,
thermal conduction by heated belt. Dwell times vary
between 50 and 300 seconds depending on heating
method. Typical reflow temperatures range from
215 to 250
°
C.
Preheating is necessary to dry the paste and evaporate
the binding agent. Preheating duration: 45 minutes at
45
°
C.
Wave soldering
Wave soldering is
not
recommended for SSOP packages.
This is because of the likelihood of solder bridging due to
closely-spaced leads and the possibility of incomplete
solder penetration in multi-lead devices.
If wave soldering cannot be avoided, the following
conditions must be observed:
A double-wave (a turbulent wave with high upward
pressure followed by a smooth laminar wave)
soldering technique should be used.
The longitudinal axis of the package footprint must
be parallel to the solder flow and must incorporate
solder thieves at the downstream end.
Even with these conditions, only consider wave
soldering SSOP packages that have a body width of
4.4 mm, that is SSOP16 (SOT369-1) or
SSOP20 (SOT266-1)
.
During placement and before soldering, the package must
be fixed with a droplet of adhesive. The adhesive can be
applied by screen printing, pin transfer or syringe
dispensing. The package can be soldered after the
adhesive is cured.
Maximum permissible solder temperature is 260
°
C, and
maximum duration of package immersion in solder is
10 seconds, if cooled to less than 150
°
C within
6 seconds. Typical dwell time is 4 seconds at 250
°
C.
A mildly-activated flux will eliminate the need for removal
of corrosive residues in most applications.
Repairing soldered joints
Fix the component by first soldering two diagonally-
opposite end leads. Use only a low voltage soldering iron
(less than 24 V) applied to the flat part of the lead. Contact
time must be limited to 10 seconds at up to 300
°
C. When
using a dedicated tool, all other leads can be soldered in
one operation within 2 to 5 seconds between
270 and 320
°
C.
相關PDF資料 |
PDF描述 |
|---|---|
| TSA5518M | 1.3 GHz bidirectional I2C-bus controlled synthesizer |
| TSM5 | Analog IC |
| TFM5 | Transient Voltage Suppressor Diodes |
| TSM600-250 | PolySwitch PTC Devices Overcurrent Protection Device |
| TSM67V05-L35CRQ | x8 Dual-Port SRAM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| TSM55N03 | 制造商:TSC 制造商全稱:Taiwan Semiconductor Company, Ltd 功能描述:N-Channel Enhancement Mode MOSFET |
| TSM55N03_07 | 制造商:TSC 制造商全稱:Taiwan Semiconductor Company, Ltd 功能描述:25V N-Channel MOSFET |
| TSM55N03_08 | 制造商:TSC 制造商全稱:Taiwan Semiconductor Company, Ltd 功能描述:25V N-Channel MOSFET |
| TSM55N03CP | 功能描述:MOSFET 25V N channel MOSFET RoHS:否 制造商:STMicroelectronics 晶體管極性:N-Channel 汲極/源極擊穿電壓:650 V 閘/源擊穿電壓:25 V 漏極連續電流:130 A 電阻汲極/源極 RDS（導通）:0.014 Ohms 配置:Single 最大工作溫度: 安裝風格:Through Hole 封裝 / 箱體:Max247 封裝:Tube |
| TSM55N03CP R0 | 制造商:SKMI/Taiwan 功能描述:TO-252;30V 55AMP N CHANEL MOSF |
發布緊急采購，3分鐘左右您將得到回復。