欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號： UBA2051A
廠商： NXP Semiconductors N.V.
英文描述： One-chip telephone ICs with speech, dialler and ringer functions
中文描述： 一個有語言，撥號及振鈴電話集成電路芯片的功能
文件頁數： 48/52頁
文件大?。?/td> 292K
代理商： UBA2051A
2000 May 19
48
Philips Semiconductors
Product specification
One-chip telephone ICs with speech,
dialler and ringer functions
UBA2050(A); UBA2051(A;C)
SOLDERING
Introduction to soldering surface mount packages
Thistextgivesaverybriefinsighttoacomplextechnology.
A more in-depth account of soldering ICs can be found in
our “Data Handbook IC26; Integrated Circuit Packages”
(document order number 9398 652 90011).
There is no soldering method that is ideal for all surface
mount IC packages. Wave soldering is not always suitable
for surface mount ICs, or for printed-circuit boards with
high population densities. In these situations reflow
soldering is often used.
Reflow soldering
Reflow soldering requires solder paste (a suspension of
fine solder particles, flux and binding agent) to be applied
to the printed-circuit board by screen printing, stencilling or
pressure-syringe dispensing before package placement.
Several methods exist for reflowing; for example,
infrared/convection heating in a conveyor type oven.
Throughput times (preheating, soldering and cooling) vary
between 100 and 200 seconds depending on heating
method.
Typical reflow peak temperatures range from
215 to 250
°
C. The top-surface temperature of the
packages should preferable be kept below 230
°
C.
Wave soldering
Conventional single wave soldering is not recommended
forsurfacemountdevices(SMDs)orprinted-circuitboards
with a high component density, as solder bridging and
non-wetting can present major problems.
To overcome these problems the double-wave soldering
method was specifically developed.
If wave soldering is used the following conditions must be
observed for optimal results:
Use a double-wave soldering method comprising a
turbulent wave with high upward pressure followed by a
smooth laminar wave.
For packages with leads on two sides and a pitch (e):
– larger than or equal to 1.27 mm, the footprint
longitudinal axis is
preferred
to be parallel to the
transport direction of the printed-circuit board;
– smaller than 1.27 mm, the footprint longitudinal axis
must
be parallel to the transport direction of the
printed-circuit board.
The footprint must incorporate solder thieves at the
downstream end.
Forpackageswithleadsonfoursides,thefootprintmust
be placed at a 45
°
angle to the transport direction of the
printed-circuit board. The footprint must incorporate
solder thieves downstream and at the side corners.
During placement and before soldering, the package must
be fixed with a droplet of adhesive. The adhesive can be
applied by screen printing, pin transfer or syringe
dispensing. The package can be soldered after the
adhesive is cured.
Typical dwell time is 4 seconds at 250
°
C.
A mildly-activated flux will eliminate the need for removal
of corrosive residues in most applications.
Manual soldering
Fix the component by first soldering two
diagonally-opposite end leads. Use a low voltage (24 V or
less) soldering iron applied to the flat part of the lead.
Contact time must be limited to 10 seconds at up to
300
°
C.
When using a dedicated tool, all other leads can be
soldered in one operation within 2 to 5 seconds between
270 and 320
°
C.
相關PDF資料
PDF描述
UBA2051AT One-chip telephone ICs with speech, dialler and ringer functions
UBA2051C One-chip telephone ICs with speech, dialler and ringer functions
UBA2051CT One-chip telephone ICs with speech, dialler and ringer functions
UBA2051T One-chip telephone ICs with speech, dialler and ringer functions
UBA2070 8-bit MCU for automotive with 16 to 60 Kbyte Flash, ADC, CSS, 5 timers, SPI, SCI, I2C interface
相關代理商/技術參數
參數描述
UBA2051AT 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:One-chip telephone ICs with speech, dialler and ringer functions
UBA2051C 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:One-chip telephone ICs with speech, dialler and ringer functions
UBA2051CT 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:One-chip telephone ICs with speech, dialler and ringer functions
UBA2051T 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:One-chip telephone ICs with speech, dialler and ringer functions
UBA2070 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:600 V CCFL ballast driver IC
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*
主站蜘蛛池模板： 伽师县| 福贡县| 卫辉市| 钟祥市| 新建县| 昆明市| 龙口市| 江口县| 琼结县| 察雅县| 汨罗市| 新余市| 濮阳市| 南康市| 射洪县| 依兰县| 武川县| 申扎县| 莲花县| 宁乡县| 邢台市| 昭苏县| 清丰县| 灵武市| 灌云县| 卫辉市| 洞口县| 广安市| 神池县| 桐梓县| 安陆市| 汶川县| 新安县| 芦山县| 南靖县| 昭觉县| 濮阳市| 阿勒泰市| 达日县| 新营市| 铁岭县|