- 您現在的位置：買賣IC網 > PDF目錄382720 > UCB1200BE (NXP SEMICONDUCTORS) Advanced modem/audio analog front-end PDF資料下載
參數資料
| 型號： | UCB1200BE |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 調制器/解調器 |
| 英文描述： | Advanced modem/audio analog front-end |
| 中文描述： | MODEM-SUPPORT CIRCUIT, PQFP48 |
| 封裝： | 7 X 7 MM, 1.40 MM HEIGHT, PLASTIC, SOT-313-2, LQFP-48 |
| 文件頁數： | 8/54頁 |
| 文件大小： | 1052K |
| 代理商： | UCB1200BE |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁
1998 Jul 22
8
Philips Semiconductors
Product specification
Advanced modem/audio analog front-end
UCB1200
The audio sample rate (f
sa
) is derived from the SIB interface clock pin (SIBCLK) and is programmable through the SIB
interface using AUD_DIV[n]. The audio sample rate is given by the following equation:
2
f
×
(
)
AUD_DIV[n]
×
)
(8 < AUD_DIV[n] < 128)
For example, a serial clock of 9.216 MHz, with a divisor of 12, results in an audio sample rate of 24.0 kHz. Both the rising
and the falling edges of SIBCLK are used in case AUD_DIV[n] is set to an odd number, which demands a 50% duty cycle
of SIBCLK to obtain time equidistant sampling.
The UCB1200 audio codec input path accepts microphone signals directly, only a DC blocking capacitor is needed since
the MICP input is biased around 1.4V. The ‘ground’ side of the microphone is either connected to the analog ground
(V
ssa1
) or to the MICGND pin. The latter will decrease the current consumption of active microphones, since the MICGND
pin is made Hi-Z when the audio codec input path is disabled.
The full scale input voltage of the audio input path is programmable in 1.5 dB steps by setting the appropriate number in
AUDIO_GAIN[n] in the audio control register A.
A clip detection circuit will inform the user whenever the input voltage exceeds the maximum input voltage, since this will
lead to a high distortion. In that case AUD_CLIP_STAT in the audio control register B is set. When ACLIP_RIS_INT is
set, an interrupt is generated on the IRQOUT pin on the rising edge of the clip detect signal. When ACLIP_FAL_INT is
set, an interrupt is generated on the falling edge of the clip detect signal.
The frequency response of the audio codec depends mainly on the selected sample rate, since the bandwidth is limited
in the down and up sampling filters. These digital filters both contain several FIR and IIR low pass filters and a DC
removal filter (high pass filter). A 3rd order smoothing filter is implemented in the DAC path, between DAC and speaker
driver stage to reduce the spurious frequencies at the speaker outputs.
f
sa
-64
=
Fig.4 Possible microphone connections.
PASSIVE
V
DDA1
1
7
21
MICP
MICGND
20
V
SSA1
18
ACTIVE
V
DDA1
1
7
21
MICP
MICGND
20
V
SSA1
18
UCB1200
UCB1200
相關PDF資料 |
PDF描述 |
|---|---|
| UCB1300 | Advanced modem/audio analog front-end |
| UCB1300BE | Advanced modem/audio analog front-end |
| UCB1400BE | Audio codec with touch screen controller and power management monitor |
| UCB1400 | Audio codec with touch screen controller and power management monitor |
| UCB1500 | PCI to AC97 bridge/host controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| UCB1300 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Advanced modem/audio analog front-end |
| UCB1300BE | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Advanced modem/audio analog front-end |
| UCB1400 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Audio codec with touch screen controller and power management monitor |
| UCB1400BE | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Audio codec with touch screen controller and power management monitor |
| UCB1400BE,128 | 功能描述:接口—CODEC AUDIO CODEC WITH TOUCHSCREEN RoHS:否 制造商:Texas Instruments 類型: 分辨率: 轉換速率:48 kSPs 接口類型:I2C ADC 數量:2 DAC 數量:4 工作電源電壓:1.8 V, 2.1 V, 2.3 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:DSBGA-81 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。