- 您現在的位置：買賣IC網 > PDF目錄382720 > UDA1325 (NXP Semiconductors N.V.) Universal Serial Bus USB CODEC PDF資料下載
參數資料
| 型號： | UDA1325 |
| 廠商： | NXP Semiconductors N.V. |
| 元件分類： | Codec |
| 英文描述： | Universal Serial Bus USB CODEC |
| 中文描述： | 通用串行總線解碼器 |
| 文件頁數： | 31/52頁 |
| 文件大小： | 310K |
| 代理商： | UDA1325 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁當前第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁
1999 May 10
31
Philips Semiconductors
Preliminary specification
Universal Serial Bus (USB) CODEC
UDA1325
COMMAND DESCRIPTIONS
Command procedure
This chapter describes the commands that can be used by
the microcontroller to control the USB processor. There
are three basic types of commands:
Initialization commands
Data flow commands
General commands.
A command is represented by an 8 bit code. It can be
followed by one or more data write cycles or one or more
read cycles or a combination. The PSIE_MMU_READY
output connected to Port 3.4 of the microcontroller
indicates that the previous action (command write, data
read or data write) has completed. A new action can only
be initiated if PSIE_MMU_READY is TRUE. The data is
valid from the moment PSIE_MMU_READY becomes
TRUE.
The PSIE contains a number of interrupt registers, one for
each endpoint. Every time a transition occurs, the interrupt
flag for the involved endpoint is set. The PSIE_MMU_INT
connected to Port 3.3 is an OR function of all interrupt
registers.
Initialization commands
Initialization commands are used during the enumeration
process of the USB network. They are used to set the USB
assigned address, enable endpoints and select the
configuration of the device.
S
ET ADDRESS
/
ENABLE
Command: D0h.
Data: write 1 byte.
The set address/enable command is used to set the USB
assigned address and enable the function. The device
always powers up disabled and should be enabled after a
bus reset.
0
Address
Enable
0
1
2
3
4
5
6
7
0
0
0
0
0
0
0
Power On Value
Table 24
R
EAD ADDRESS
/
ENABLE
Command: D0h.
Data: read 1 byte.
The read address/enable command is used to read the
USB assigned address and the enable bit of the device.
The format of the data phase is the same as for the set
address/enable command.
S
ET ENDPOINT ENABLE
Command: D8h.
Data: write 1 byte.
The set endpoint enable command is used to set the
enable bits for the non default endpoints.
If the enable bit is ‘1’, the non default endpoints are
enabled, if ‘0’, the non default endpoints are disabled.
The function then only responds to the default control
endpoint.
After bus reset, the enable bit is set to ‘0’.
R
EAD ENDPOINT ENABLE
Command: D8h.
Data: read 1 byte.
The read endpoint enable command is used to read the
enable bit for the non default endpoints of the function.
The format of the data phase is the same as for the set
endpoint enable command.
S
ET MODE
Command: F3h.
Data: write 1 byte.
BIT
DESCRIPTION
Address
the value written becomes
the device address
a ‘1’ enables this function
Enable
X
X
X
X
X
X
X
0
Enable
Reserved
7
6
5
4
3
2
1
0
Power On Value
相關PDF資料 |
PDF描述 |
|---|---|
| UDA1325H | Universal Serial Bus USB CODEC |
| UDA1325PS | Universal Serial Bus USB CODEC |
| UDA1326PS | USB AUDIO-CODEC(通用串行總線音頻編解碼器) |
| UDA1331H | Universal Serial Bus USB Audio Playback Peripheral APP |
| UDA1334BT | Low power audio DAC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| UDA1325H | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Universal Serial Bus USB CODEC |
| UDA1325PS | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Universal Serial Bus USB CODEC |
| UDA1328 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Multi-channel filter DAC |
| UDA1328T | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Multi-channel filter DAC |
| UDA1330A | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Low-cost stereo filter DAC |
發布緊急采購，3分鐘左右您將得到回復。