- 您現在的位置：買賣IC網 > Datasheet目錄58 > XIB-E (Digi International/Maxstream)BOARD INTERFACE ETHERNET Datasheet資料下載
參數資料
| 型號： | XIB-E |
| 廠商： | Digi International/Maxstream |
| 文件頁數： | 30/64頁 |
| 文件大小： | 1858K |
| 描述： | BOARD INTERFACE ETHERNET |
| 標準包裝： | 1 |
| 附件類型： | 接口板 |
| 適用于相關產品： | XStream 和 Xcite 收音機 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁當前第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁
XStream"燨EM燫F燤odule?燩roduct燤anual爒5.x00燵2006.02.24]?/DIV>
RO (Packetization Timeout) Command
AT Command: ATRO
Binary Command: 0x21 (33 decimal)
Parameter Range: 0 0xFFFF [x 200 祍]
Default Parameter Value: 0
Number of bytes returned: 2
Minimum Firmware Version Required: 4.2A
<Serial Interfacing> Set/Read the time of silence
(no bytes received) after which transmission
begins. After a serial byte is received and if no
other byte is received before the RO timeout, the
transmission will start.
RP (RSSI PWM Timer) Command
<Diagnostics> RP Command is used to enable
PWM (Pulse Width Modulation) output on the
CONFIG pin. The output is calibrated to show the
level the received RF signal is above the
sensitivity level of the module. The PWM pulses
vary from zero to 95 percent. Zero percent
means the received RF signal is at or below the
published sensitivity level of the module. The
following table shows levels above sensitivity and PWM values.
AT Command: ATRP
Binary Command: 0x22 (34 decimal)
Parameter Range: 0 - 0x7F
[x 100 milliseconds]
Default Parameter Value: 0 (disabled)
Number of bytes returned: 1
Minimum Firmware Version Required: 4.2A
The total period of the PWM output is 8.32 ms. Because there are 40 steps in the PWM output;
the minimum step size is 0.208 ms.
Table?03. PWM燙hart?/DIV>
dBm above Sensitivity
PWM percentage
(high period / total period)
10
47.5%
20
62.5%
30
77.5%
A non-zero value defines the time that the PWM output will be active with the RSSI value of the
last received RF packet. After the set time when no RF packets are received, the PWM output will
be set low (0 percent PWM) until another RF packet is received. The PWM output will also be set
low at power-up. A parameter value of 0xFF permanently enables the PWM output and it will
always reflect the value of the last received RF packet.
PWM output shares the Config input pin. When the module is powered, the Config pin will be an
input. During the power-up sequence, the Config pin will be read to determine whether the
module is going into AT Command Mode. After this, if RP parameter is a non-zero value, the
Config pin will be configured as an output and set low until the first RF packet is received. With a
non-zero RP parameter, the Config pin will be an input for RP ms after power up.
RR (Retries) Command
<Networking> Set/Read the number of retries
that can be sent for a given RF packet. Once RR
command is enabled (set to a non-zero value),
RF packet acknowledgements and retries are
enabled. After transmitting a packet, the
transmitter will wait to receive an
acknowledgement from a receiver. If the
acknowledgement is not received in the period of time specified by the RN (Delay Slots)
Command, the transmitter will transmit the original packet again. The packet will be transmitted
repeatedly until an acknowledgement is received or until the packet has been sent RR times.
AT Command: ATRR
Binary Command: 0x18 (24 decimal)
Parameter Range: 0 0xFF
Default Parameter Value: 0 (disabled)
Number of bytes returned: 1
Minimum Firmware Version Required: 4.22
Note: For retries to work correctly, all modules in the system must have retries enabled.
牋牘?006燤axStream,營nc.燙onfidential燼nd燩roprietary?/DIV>
30?/DIV>
相關PDF資料 |
PDF描述 |
|---|---|
| XIB-R | BOARD INTERFACE RS232/485 |
| ZMN2400HPDB | BOARD ROUTER DEV ZIGBEE 100MW |
| ZMN24HPDK-B | KIT DEV W/ZIGBEE ZMN2400HP |
| ZNI1000TC | IC TEMP SENSOR NI1000 SOT23-3 |
| 02110102-000 | SNSR TILT RATIO 60DEG 500MA FLNG |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XIB-R | 功能描述:界面模塊 RS-232/485 interface 24XStream 9XCite RoHS:否 制造商:4D Systems 產品:Serial Converters 通道/端口數量: 數據速率: 接口類型:USB, UART 工作電源電壓:3.3 V, 5 V 最大工作溫度: |
| XIB-U | 功能描述:界面模塊 USB interface board 24XStream 9XCite RoHS:否 制造商:4D Systems 產品:Serial Converters 通道/端口數量: 數據速率: 接口類型:USB, UART 工作電源電壓:3.3 V, 5 V 最大工作溫度: |
| XIC25040 | 制造商:XIC 功能描述:25040 24HR '6 |
| XILINXPWR-079 | 功能描述:電源管理IC開發工具 Pow Mgt Eval Mod for Xilinx FPGAs RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| XILINXPWR-080 | 功能描述:電源管理IC開發工具 Pow Mgt Eval Mod for Xilinx FPGAs RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
發布緊急采購，3分鐘左右您將得到回復。