- 您現在的位置：買賣IC網 > Datasheet目錄58 > XIB-R (Digi International/Maxstream)BOARD INTERFACE RS232/485 Datasheet資料下載
參數資料
| 型號： | XIB-R |
| 廠商： | Digi International/Maxstream |
| 文件頁數： | 19/36頁 |
| 文件大小： | 826K |
| 描述： | BOARD INTERFACE RS232/485 |
| 標準包裝： | 1 |
| 附件類型： | 接口板 |
| 適用于相關產品： | XStream 和 Xcite 收音機 |
| 其它名稱： | Q2231853 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
9XCite"燨EM燫F燤odule?燩roduct燤anual爒2.1燵2007.01.04]
2007燤axStream,營nc.
牋牋?9
3.4. Automatic DIP Switch Configurations
Each time the RF Modem is powered-on, intelligence on the Max-
Stream Interface Board (located inside the RF Modem) sends AT
Commands that program the modem based on positions of the DIP
Switch. Automatic configurations that take place during the power-on
sequence affect RF Modem parameter values as shown below.
To avoid overwriting previously stored custom configurations (due to the automatic configurations
that take place each time the RF Modem is powered-on), it is necessary to disable a processor
located on the XIB-R interface board. To disable the processor, populate J7 of the XIB-R Interface
Board. (By default, J7 jumper is not populated.)
Table?03. RF燤odem燩owerup燨ptions?J7爅umper燼nd燙onfig燬witch)
AT燙ommands燬ent燼s爎esult爋f燚IP燬witch燬ettings?SW?燚IP燬witch)
Condition
Behavior
If J7 is populated
Processor is disabled and AT Commands are not sent to the RF Modem
If Config Switch is pressed
Processor is disabled and RF Modem enters into AT Command Mode
If J7 is NOT populated and Config
Switch is NOT pressed
Execute logic as shown in Table 6.
Condition
Behavior
Serial Interfacing Options
If SW1 is ON (up)
AT Commands sent: ATCS 0 (RS-232 Operation: CTS
function for CTS
line)
ATCD 2 (DO3 - RX LED = low)
If SW1 is OFF (down)
AT Commands sent: ATCS 3 (RS-485 or RS-422 Operation)
ATCD 2 (DO3 - RX LED = low)
Exit AT Command Mode
Always
AT Commands sent: ATCN (Exit AT Command Mode)
相關PDF資料 |
PDF描述 |
|---|---|
| ZMN2400HPDB | BOARD ROUTER DEV ZIGBEE 100MW |
| ZMN24HPDK-B | KIT DEV W/ZIGBEE ZMN2400HP |
| ZNI1000TC | IC TEMP SENSOR NI1000 SOT23-3 |
| 02110102-000 | SNSR TILT RATIO 60DEG 500MA FLNG |
| 1-5209285-2 | FOPC BOA 12DB FC/UPC BP SM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XIB-U | 功能描述:界面模塊 USB interface board 24XStream 9XCite RoHS:否 制造商:4D Systems 產品:Serial Converters 通道/端口數量: 數據速率: 接口類型:USB, UART 工作電源電壓:3.3 V, 5 V 最大工作溫度: |
| XIC25040 | 制造商:XIC 功能描述:25040 24HR '6 |
| XILINXPWR-079 | 功能描述:電源管理IC開發工具 Pow Mgt Eval Mod for Xilinx FPGAs RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| XILINXPWR-080 | 功能描述:電源管理IC開發工具 Pow Mgt Eval Mod for Xilinx FPGAs RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| XILINXPWR-081 | 功能描述:電源管理IC開發工具 Pwr Mgmt Eval Mod Xilinx RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
發布緊急采購，3分鐘左右您將得到回復。