- 您現在的位置：買賣IC網 > Datasheet目錄58 > XIB-R (Digi International/Maxstream)BOARD INTERFACE RS232/485 Datasheet資料下載
參數資料
| 型號： | XIB-R |
| 廠商： | Digi International/Maxstream |
| 文件頁數： | 28/36頁 |
| 文件大小： | 826K |
| 描述： | BOARD INTERFACE RS232/485 |
| 標準包裝： | 1 |
| 附件類型： | 接口板 |
| 適用于相關產品： | XStream 和 Xcite 收音機 |
| 其它名稱： | Q2231853 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁當前第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
9XCite"燨EM燫F燤odule?燩roduct燤anual爒2.1燵2007.01.04]
2007燤axStream,營nc.
牋牋?8
SM (Sleep Mode) Parameter
<Non-AT Settable Parameter: Sleep Mode (Low
Power)> SM Parameter is used to adjust Sleep
Mode settings. By default, Sleep Mode is disabled
and the radio modem remains continually active.
SM Parameter allows the radio modem to run in a
lower-power state and be configured in one of
eight settings.
Cyclic Sleep settings wake the radio modem after
the amount of time designated by SM Command.
If the radio modem detects a wake-up initializer
during the time it is awake, it will synchronize
with the transmitting radio modem and start
receiving data after the wake-up initializer runs
its duration. Otherwise, it returns to Sleep Mode
and continue to cycle in and out of sleep until the
wake-up initializer is detected. If a Cyclic Sleep
setting is chosen, the ST, LH and HT parameters
must also be set as described in the "Sleep Mode" section of this manual.
ST (Time before Sleep) Parameter
<Non-AT Settable Parameter: Sleep Mode (Low Power)> ST Parameter sets the period of time (in
tenths of seconds) in which the radio modem remains inactive before entering into Sleep Mode.
For example, if the ST Parameter is set to 0x64 ("100" decimal), the radio modem will enter into
Sleep Mode after 10 seconds of inactivity (no transmitting or receiving). This command can only
be used if either Cyclic Sleep or Serial Port Sleep Mode settings have been selected using SM
(Sleep Mode) Parameter.
Parameter Range: 0x10 - 0xFFFF [x 100 ms]
# of bytes returned: 2
Default Parameter Value: 0x64 ("100" decimal)
Related Parameters: SM (Sleep Mode), LH (Wake-up Initializer Timer), HT (Time before Wake-
up Initializer)
VR (Firmware Version) Command
<AT Command: AT Command Options> Reads and returns the currently loaded firmware version
of the XCite Radio Modem.
AT Command: VR
Parameter Range: 0 - 0xFFFF [Read-only]
# of bytes returned: 2
WR (Write) Command
<AT Command: (Special)> WR Command writes all configurable parameters to non-volatile mem-
ory. Using WR Command saves parameters to the radio modem's persistent memory. (This means
that the parameters remain in the radio modem's memory until explicitly overwritten by future
uses of WR Command.)
AT Command: WR
Parameter Ranges: 0 - 8
Parameter
Configuration
0
No Sleep
1
Pin Sleep
2
Serial Port Sleep
3
Cyclic 0.5 seconds
4
Cyclic 1.0 seconds
5
Cyclic 2.0 seconds
6
Cyclic 4.0 seconds
7
Cyclic 8.0 seconds
8
Cyclic 16.0 seconds
Default Parameter Value: 0
Number of bytes returned: 1
相關PDF資料 |
PDF描述 |
|---|---|
| ZMN2400HPDB | BOARD ROUTER DEV ZIGBEE 100MW |
| ZMN24HPDK-B | KIT DEV W/ZIGBEE ZMN2400HP |
| ZNI1000TC | IC TEMP SENSOR NI1000 SOT23-3 |
| 02110102-000 | SNSR TILT RATIO 60DEG 500MA FLNG |
| 1-5209285-2 | FOPC BOA 12DB FC/UPC BP SM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XIB-U | 功能描述:界面模塊 USB interface board 24XStream 9XCite RoHS:否 制造商:4D Systems 產品:Serial Converters 通道/端口數量: 數據速率: 接口類型:USB, UART 工作電源電壓:3.3 V, 5 V 最大工作溫度: |
| XIC25040 | 制造商:XIC 功能描述:25040 24HR '6 |
| XILINXPWR-079 | 功能描述:電源管理IC開發工具 Pow Mgt Eval Mod for Xilinx FPGAs RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| XILINXPWR-080 | 功能描述:電源管理IC開發工具 Pow Mgt Eval Mod for Xilinx FPGAs RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| XILINXPWR-081 | 功能描述:電源管理IC開發工具 Pwr Mgmt Eval Mod Xilinx RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
發布緊急采購，3分鐘左右您將得到回復。