- 您現在的位置：買賣IC網 > Datasheet目錄58 > XIB-R (Digi International/Maxstream)BOARD INTERFACE RS232/485 Datasheet資料下載
參數資料
| 型號： | XIB-R |
| 廠商： | Digi International/Maxstream |
| 文件頁數： | 26/36頁 |
| 文件大小： | 826K |
| 描述： | BOARD INTERFACE RS232/485 |
| 標準包裝： | 1 |
| 附件類型： | 接口板 |
| 適用于相關產品： | XStream 和 Xcite 收音機 |
| 其它名稱： | Q2231853 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁當前第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
9XCite"燨EM燫F燤odule?燩roduct燤anual爒2.1燵2007.01.04]
2007燤axStream,營nc.
牋牋?6
MK (Address Mask) Command
<AT Command: Networking> MK Command is used to set the radio modem address mask. All RF
packets contain the Destination Address of the transmitting radio modem. When an RF packet is
received, the transmitter's Destination Address is logically "ANDed" (bitwise) with the Address
Mask of the receiver. The resulting value must match the Destination Address or the Address Mask
of the receiver for the packet to be received and sent out the receiving modem serial port. If the
"ANDed" value does not match either the Destination Address or the Address Mask of the receiver,
the packet is discarded. (All "0" values are treated as "irrelevant" values and ignored.)
AT Command: MK
Parameter Range: 0 - 0xFFFF
# of bytes returned: 2
Default Parameter Value: 0xFFFF (When set to this value, the Destination Address of the trans-
mitter must exactly match the Destination Address of the receiver.)
Related Commands: DT (Destination Address), HP (Channel)
NB (Parity) Parameter
<Non-AT Settable Parameter: Serial Interfacing>
NB Parameter allows parity for the modem to be
changed. Parity is an error detection method in
which a bit (0 or 1) is added to each group of bits
so that it will have either an odd number of 1's or
an even number of 1's. For example, if parity is
odd, then any group of bits that arrives with an
even number of 1's must contain an error.
PW (Pin Wake-up) Parameter
<Non-AT Settable Parameter: Sleep (Low
Power)> Under normal operation, a radio modem
in Cyclic Sleep Mode cycles from an active state to
a low-power state at regular intervals until data is
ready to be received. If PW Parameter is set to 1,
the SLEEP Pin (Pin 2 of the embedded OEM RF
Module) can be used to awaken the modem from
Cyclic Sleep. If the SLEEP Pin is de-asserted
(low), the radio modem will be fully operational
and will not go into Cyclic Sleep. Once SLEEP is asserted, the radio modem will remain active for
the period of time specified by ST (Time before Sleep) Command, and will return to Cyclic Sleep
Mode (if no data is ready to be transmitted). PW Command is only valid if Cyclic Sleep has been
enabled using SM Command.
RE (Restore Defaults) Command
<AT Command: AT Command Options> RE Command restores all AT-settable parameters to fac-
tory default settings. However, RE Command will not write the default values to non-volatile mem-
ory. Unless the WR (Write) Command is issued after the RE Command, the default settings will not
be saved in the event of radio modem reset or power-down.
AT Command: RE
Related Command: WR (Write)
Parameter Ranges: 0 - 4
Parameter
Configuration
0
8-bit (no parity) or 7-
bit (with any parity)
1
8-bit even parity
2
8-bit odd parity
3
8-bit mark parity
4
8-bit space parity
Default Parameter Value: 0
Number of bytes returned: 1
Parameter Ranges: 0 - 1
Parameter
Configuration
0
disabled
1
enabled
Default Parameter Value: 0
Number of bytes returned: 1
相關PDF資料 |
PDF描述 |
|---|---|
| ZMN2400HPDB | BOARD ROUTER DEV ZIGBEE 100MW |
| ZMN24HPDK-B | KIT DEV W/ZIGBEE ZMN2400HP |
| ZNI1000TC | IC TEMP SENSOR NI1000 SOT23-3 |
| 02110102-000 | SNSR TILT RATIO 60DEG 500MA FLNG |
| 1-5209285-2 | FOPC BOA 12DB FC/UPC BP SM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| XIB-U | 功能描述:界面模塊 USB interface board 24XStream 9XCite RoHS:否 制造商:4D Systems 產品:Serial Converters 通道/端口數量: 數據速率: 接口類型:USB, UART 工作電源電壓:3.3 V, 5 V 最大工作溫度: |
| XIC25040 | 制造商:XIC 功能描述:25040 24HR '6 |
| XILINXPWR-079 | 功能描述:電源管理IC開發(fā)工具 Pow Mgt Eval Mod for Xilinx FPGAs RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| XILINXPWR-080 | 功能描述:電源管理IC開發(fā)工具 Pow Mgt Eval Mod for Xilinx FPGAs RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
| XILINXPWR-081 | 功能描述:電源管理IC開發(fā)工具 Pwr Mgmt Eval Mod Xilinx RoHS:否 制造商:Maxim Integrated 產品:Evaluation Kits 類型:Battery Management 工具用于評估:MAX17710GB 輸入電壓: 輸出電壓:1.8 V |
發(fā)布緊急采購，3分鐘左右您將得到回復。