- 您現在的位置：買賣IC網 > PDF目錄30701 > 48SD3208RPFK (MAXWELL TECHNOLOGIES) CAP 1.5UF 50V CERAMIC MONO 20% PDF資料下載
參數資料
| 型號： | 48SD3208RPFK |
| 廠商： | MAXWELL TECHNOLOGIES |
| 元件分類： | DRAM |
| 英文描述： | CAP 1.5UF 50V CERAMIC MONO 20% |
| 中文描述： | 32M X 8 SYNCHRONOUS DRAM, 6 ns, PDFP72 |
| 封裝： | DFP-72 |
| 文件頁數： | 30/39頁 |
| 文件大小： | 589K |
| 代理商： | 48SD3208RPFK |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁當前第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁
48SD3208
M
em
o
ry
36
All data sheets are subject to change without notice
2005 Maxwell Technologies
All rights reserved.
256Mb (8-Meg X 8-Bit X 4-Banks) SDRAM
01.10.05 Rev 2
power-down mode, and command input is enabled from the next clock. In this mode, internal refresh is not
performed.
Clock suspend mode: By driving CKE to Low during a bank-active or read/write operation, the SDRAM
enters clock suspend mode. During clock suspend mode, external input signals are ignored and the internal
state is maintained. When CKE is driven High, the SDRAM terminates clock suspend mode, and command
input is enabled from the next clock. For more details, refer to the “CKE Truth Table”.
Power-up sequence: The SDRAM should use the following sequence during power-up:
The CLK, CKE, CS, DQM and DQ pins stay low until power stabilizes.
The CLK pin is stable within 100ms after power stabilizes before the following initialization sequence.
The CKE and DQM is driven high between when power stabilizes and the initialization sequence.
This SDRAM has V
CC clamp diodes for CLK, CKE, CS, DQM and DQ pins. If these pins go high before
power up, the large current flows from these pins to V
CC through the diodes.
Initialization sequence: When 200ms or more has past after the power up sequence, all banks must be
precharged using the precharge command (PALL). After t
RP delay, set 8 or more auto refresh commands
(REF). Set the mode register set command (MRS) to initialize the mode register. It is recommended that by
keeping DQM and CKE High, the output buffer becomes High-Z during initialization sequence, to avoid DQ
bus contention on a memory system formed with a number of devices.
相關PDF資料 |
PDF描述 |
|---|---|
| 48SD3208RPFE | 256 Mb SDRAM 8-Meg X 8-Bit X 4-Banks |
| 48SD3208RPFH | 256 Mb SDRAM 8-Meg X 8-Bit X 4-Banks |
| 48SD3208RPFI | CAP 1.5UF 50V CERAMIC MONO 20% |
| 48SD3208 | 256 Mb SDRAM 8-Meg X 8-Bit X 4-Banks |
| 48SD6404RPFE | CAP 1200PF 100V CERAMIC MONO 5% |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 48SD6404 | 制造商:MAXWELL 制造商全稱:Maxwell Technologies 功能描述:256 Mb SDRAM 16-Meg X 4-Bit X 4-Banks |
| 48SD6404RPFE | 制造商:MAXWELL 制造商全稱:Maxwell Technologies 功能描述:256 Mb SDRAM 16-Meg X 4-Bit X 4-Banks |
| 48SD6404RPFH | 制造商:MAXWELL 制造商全稱:Maxwell Technologies 功能描述:256 Mb SDRAM 16-Meg X 4-Bit X 4-Banks |
| 48SD6404RPFI | 制造商:MAXWELL 制造商全稱:Maxwell Technologies 功能描述:256 Mb SDRAM 16-Meg X 4-Bit X 4-Banks |
| 48SD6404RPFK | 制造商:MAXWELL 制造商全稱:Maxwell Technologies 功能描述:256 Mb SDRAM 16-Meg X 4-Bit X 4-Banks |
發布緊急采購，3分鐘左右您將得到回復。