- 您現在的位置：買賣IC網 > PDF目錄369244 > 7005 (Aeroflex Inc.) ACT7005/7006 Single Package Solution Dual Transceiver, Protocol, Subsystem PDF資料下載
參數資料
| 型號： | 7005 |
| 廠商： | Aeroflex Inc. |
| 英文描述： | ACT7005/7006 Single Package Solution Dual Transceiver, Protocol, Subsystem |
| 中文描述： | ACT7005/7006單一封裝解決方案雙收發器，協議，子系統 |
| 文件頁數： | 12/29頁 |
| 文件大小： | 452K |
| 代理商： | 7005 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁當前第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁
Aeroflex Circuit Technology
SCD7005 REV B 8/2/01
Plainview NY (516) 694-6700
12
described below are available and are essentially
independent. Any, all, or none may be selected.
Also, reporting of faults by the subsystem requires
that SSERR be latched (not pulsed) low until the
fault is cleared.
Resetting SSF and TF on Receipt of Valid
Commands
If ENABLE is selected and the other three option
lines are held high, then the Status Word Register
will be reset on receipt of any valid command with
the exception of Transmit Status and Transmit Last
Command. Note that in this mode, the TF will never
be seen in the Status Word, and the SSF will only be
seen if SSERR is latched low. Also note that the SSF
will not be seen in response to Transmit Status or
Transmit Last Command if the preceding Status
Word was clear, regardless of actions taken on the
SSERR line after the clear status transmission.
Status Register Update at Fault Occurrence
If STATUS UPDATE is selected (held low), then the
TF or SSF will appear in response to a Transmit
Status or Transmit Last Command issued as the first
command after the fault occurs. Any other command
(except as noted in the Preserving the BIT Word
section) will reset the TF and SSF. Repeated
Transmit Status or Transmit Last Command
immediately following the fault will continue to show
the TF and/or SSF in the Status Word. Note that this
behavior may not meet the "letter-of-the-spec" as
described in MIL-STD-1553B, but is considered the
"preferred" behavior by some users.
TF and SSF Reporting in the Next Status
Word – After the Fault
If NEXT STATUS is selected (held low), then the TF
or SSF will appear in response to the very next valid
command after the fault except for Transmit Status
or Transmit Last Command. The flag(s) will be reset
on receipt of any valid command following the status
transmission with the flag(s) set except for Transmit
Status, Transmit Last Command, or as noted in the
following section on Preserving the BIT Word.
Preserving the BIT Word
In order to preserve the Transmitter Timeout Flag,
Subsystem Handshake Failure, and Loop Test
Failure Bits in the BIT Word, it is necessary to select
BIT DECODE (hold it low). This will prevent resetting
those bits if the Transmit Bit Word Mode Command
immediately follows the fault or follows a Transmit
Last Command or Transmit Status immediately
following the fault. It will also prevent resetting the TF
and SSF Bits in the Status Word. Any other valid
commands will cause those BIT Word Bits and the
Status Word Bits to be reset.
相關PDF資料 |
PDF描述 |
|---|---|
| 7006 | ACT7005/7006 Single Package Solution Dual Transceiver, Protocol, Subsystem |
| 700B | Power Module: Custom Dc-Dc Converter, 24 V to 97 V Adjustable Output(DC-DC轉換器,24V-97V可調輸出) |
| 700SCFM | 20SCFM |
| 701011xxx | AXIAL LEAD PRECISION WIREWOUND RESISTORS |
| 70405xxx | AXIAL LEAD PRECISION WIREWOUND RESISTORS |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 700-5 | 制造商:MICROSEMI 制造商全稱:Microsemi Corporation 功能描述:RECTIFIERS ASSEMBLIES THREE PHASE BRIDGES, 2.5 AMP, STANDARD AND FAST RECOVERY |
| 70050 | 制造商:Acme Electric Corporation XXX 功能描述:TOROIDAL TRANSFORMER, Power Rating:15VA, Secondary Voltages:2 x 7V, Secondary Cu |
| 700-500 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:PCB SHEARS 30CM |
| 700-500 | 制造商:Mega Electronics Inc 功能描述:SHEAR PCB 30CM 制造商:Mega Electronics Inc 功能描述:SHEAR, PCB, 30CM 制造商:MEGA 功能描述:SHEAR, PCB, 30CM, Cutting Capacity Max:305mm, Aluminium Cutting Capacity:1.5mm, 制造商:MEGA 功能描述:SHEAR, PCB, 305MM, Cutting Capacity Max:305mm, Aluminum Cutting Capacity:1.5mm, External Depth:440mm, External Width:245mm, Cut Width Max:305mm , RoHS Compliant: NA |
| 70050-002 | 制造商:FCI 功能描述:SET SCREW - Bulk |
發布緊急采購，3分鐘左右您將得到回復。