- 您現在的位置：買賣IC網 > PDF目錄68812 > 71M6543G-IGT/F (MAXIM INTEGRATED PRODUCTS INC) SPECIALTY ANALOG CIRCUIT, PQFP100 PDF資料下載
參數資料
| 型號： | 71M6543G-IGT/F |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 模擬信號調理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PQFP100 |
| 封裝： | LEAD FREE, LQFP-100 |
| 文件頁數： | 141/157頁 |
| 文件大小： | 2178K |
| 代理商： | 71M6543G-IGT/F |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁當前第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁
71M6543F/H and 71M6543G/GH Data Sheet
84
2008–2011 Teridian Semiconductor Corporation
v1.2
Table 66: Clear Events for WAKE flags
Flag
Wake on:
Clear Events
WF_TMR
Timer expiration
WAKE falls
WF_PB
PB pin high level
WAKE falls
WF_RX
Either edge RX pin
WAKE falls
WF_DIO4
SEGDIO4 rising edge
WAKE falls
WF_DIO52
SEGDIO52 high level
WAKE falls
WF_DIO55
If OPT_RXDIS = 1 (I/O RAM 0x2457[2]),
wake on SEGDIO55 high
If OPT_RXDIS = 0
wake on either edge of OPT_RX
WAKE falls
WF_RST
RESET pin driven high
WAKE falls, WF_CSTART, WF_RSTBIT,
WF_OVF, WF_BADVDD
WF_RSTBIT
RESET bit is set (I/O RAM 0x2200[3])
WAKE falls, WF_CSTART, WF_OVF,
WF_BADVDD, WF_RST
WF_ERST
E_RST pin driven high and the ICE
interface must be enabled by driving the
ICE_E pin high.
WAKE falls, WF_CSTART, WF_RST,
WF_OVF, WF_RSTBIT
WF_OVF
Watchdog (WD) reset
WAKE falls, WF_CSTART, WF_RSTBIT,
WF_BADVDD, WF_RST
WF_CSTART
Cold-start (i.e., after the application of
first power)
WAKE falls, WF_RSTBIT, WF_OVF,
WF_BADVDD, WF_RST
Note:
“WAKE falls” implies that the internal WAKE signal has been reset, which happens automatically upon
entry into LCD mode or SLEEP mode (i.e., when the MPU sets the LCD_ONLY bit (I/O RAM 0x28B2[6]) or
the SLEEP (I/O RAM 0x28B2[7]) bit). When the internal WAKE signal resets, all wake flags are reset. Since
the various wake flags are automatically reset when WAKE falls, it is not necessary for the MPU to reset
these flags before entering LCD mode or SLEEP mode. Also, other wake events can cause the wake flag
to reset, as indicated above (e.g., the WF_RST flag can also be reset by any of the following flags setting:
WF_CSTART, WS_RSTBIT, WF_OVF, WF_BADVDD)
3.4.2
Wake on Timer
If the part is in SLP or LCD mode, it can be awakened by the Wake Timer. Until this timer times out, the
MPU is in reset due to the internal WAKE signal being low. When the Wake Timer times out, WAKE rises
and within three CK32 cycles, the MPU begins to execute. The MPU can determine that the timer woke it
by checking the WF_TMR (I/O RAM 0x28B1[2]) wake flag.
The Wake Timer begins timing when the part enters LCD or SLP mode. Its duration is controlled by the
WAKE_TMR[7:0] register (I/O RAM 0x2880). The timer duration is WAKE_TMR[7:0] +1 seconds.
The Wake Timer is armed by setting WAKE_ARM = 1 (I/O RAM 0x28B2[5]). It must be armed at least
three RTC cycles before either SLP or LCD modes are initiated. Setting WAKE_ARM presets the timer
with the value in WAKE_TMR and readies the timer to start when the MPU writes to the SLEEP (I/O RAM
0x28B2[7]) or LCD_ONLY (I/O RAM 0x28B2[6]) bits. The timer is neither reset nor disarmed when the
MPU wakes-up. Thus, once armed and set, the MPU continues to be awakened WAKE_TMR[7:0]
seconds after it requests SLP mode or LCD mode (i.e., once written, the WAKE_TMR[7:0] register holds
its value and does not have to be re-written each time the MPU enters SLP or LCD mode. Also, since
WAKE_TMR[7:0] is non-volatile, it also holds its value through resets and power failures).
3.5
Data Flow and MPU/CE Communication
The data flow between the Compute Engine (CE) and the MPU is shown in Figure 26. In a typical application,
the 32-bit CE sequentially processes the samples from the ADC inputs, performing calculations to measure
相關PDF資料 |
PDF描述 |
|---|---|
| 722BG | 2-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| 722MG | 2-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| 73M1903-IGV | SPECIALTY CONSUMER CIRCUIT, PQFP32 |
| 73M1903-IM | SPECIALTY CONSUMER CIRCUIT, QCC32 |
| 73M1903-IGV/F | SPECIALTY CONSUMER CIRCUIT, PQFP32 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 71M6543G-IGTR/F | 功能描述:計量片上系統 - SoC Precision Energy Meter IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 處理器系列:71M6511 類型:Metering SoC 最大時鐘頻率:70 Hz 程序存儲器大小:64 KB 數據 RAM 大小:7 KB 接口類型:UART 可編程輸入/輸出端數量:12 片上 ADC: 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-64 封裝:Reel |
| 71M6543GT-IGT/F | 制造商:Maxim Integrated Products 功能描述:3-PHASE, 128KK, PRES TEMP SENSOR - Bulk |
| 71M6543GT-IGTR/F | 制造商:Maxim Integrated Products 功能描述:3-PHASE, 128KK, PRES TEMP SENSOR - Tape and Reel |
| 71M6543H | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Selectable Gain of 1 or 8 for One Current Energy Meter ICs Metrology Compensation |
| 71M6543H-IGT/F | 功能描述:IC ENERGY METER 100-LQFP 制造商:maxim integrated 系列:Single Converter Technology? 包裝:托盤 零件狀態:停產 輸入阻抗:- 測量誤差:0.1% 電壓 - I/O 高:2V 電壓 - I/O 低:0.8V 電流 - 電源:- 電壓 - 電源:3 V ~ 3.6 V 表計類型:3 相 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:100-LQFP 供應商器件封裝:100-LQFP（14x14） 標準包裝:90 |
發布緊急采購，3分鐘左右您將得到回復。