- 您現在的位置：買賣IC網 > PDF目錄68812 > 71M6543GH-IGT/F (MAXIM INTEGRATED PRODUCTS INC) SPECIALTY ANALOG CIRCUIT, PQFP100 PDF資料下載
參數資料
| 型號： | 71M6543GH-IGT/F |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 模擬信號調理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PQFP100 |
| 封裝： | LEAD FREE, LQFP-100 |
| 文件頁數： | 71/157頁 |
| 文件大小： | 2178K |
| 代理商： | 71M6543GH-IGT/F |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁當前第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁
71M6543F/H and 71M6543G/GH Data Sheet
20
2008–2011 Teridian Semiconductor Corporation
v1.2
The recommended ADC multiplexer sequence samples the current first, immediately followed by
sampling of the corresponding phase voltage, thus the voltage is delayed by a phase angle
Ф relative to
the current. The delay compensation implemented in the CE aligns the voltage samples with their
corresponding current samples by first delaying the current samples by one full sample interval (i.e.,
360
o), then routing the voltage samples through the all-pass filter, thus delaying the voltage samples by
360
o -
θ, resulting in the residual phase error between the current and its corresponding voltage of θ – Ф.
The residual phase error is negligible, and is typically less than ±1.5 milli-degrees at 100Hz, thus it does
not contribute to errors in the energy measurements.
When using remote sensors, the CE performs the same delay compensation described above to align
each voltage sample with its corresponding current sample. Even though the remote current samples do
not pass through the 71M6543 multiplexer, their timing relationship to their corresponding voltages is
fixed and precisely known, provided that the MUXn_SEL[3:0] slot assignment fields are programmed as
shown in Table 1. Note that these slot assignments result in VA, VB and VC occupying multiplexer slots
3, 4 and 5, respectively (see Figure 4).
2.2.4
ADC Pre-Amplifier
The ADC pre-amplifier is a low-noise differential amplifier with a fixed gain of 8 available only on the
IADC0-IADC1 sensor input pins. A gain of 8 is enabled by setting PRE_E = 1 (I/O RAM 0x2704[5]). When
disabled, the supply current of the pre-amplifier is <10 nA and the gain is unity. With proper settings of the
PRE_E and DIFF0_E (I/O RAM 0x210C[4]) bits, the pre-amplifier can be used whether differential mode
is selected or not. For best performance, the differential mode is recommended. In order to save power,
the bias current of the pre-amplifier and ADC is adjusted according to the ADC_DIV control bit (I/O RAM
0x2200[5]).
2.2.5
A/D Converter (ADC)
A single 2
nd order sigma-delta A/D converter digitizes the voltage and current inputs to the device. The
resolution of the ADC, including the sign bit, is 21 bits (FIR_LEN[1:0] = 01, I/O RAM 0x210C[2:1]), or 22
bits (FIR_LEN[1:0] = 10). The ADC is clocked by CKADC.
Initiation of each ADC conversion is controlled by the internal MUX_CTRL circuit as described earlier. At
the end of each ADC conversion, the FIR filter output data is stored into the CE RAM location determined by
the multiplexer selection.
2.2.6
FIR Filter
The finite impulse response filter is an integral part of the ADC and it is optimized for use with the multiplexer.
The purpose of the FIR filter is to decimate the ADC output to the desired resolution. At the end of each
ADC conversion, the output data is stored into the fixed CE RAM location determined by the multiplexer
selection stored in the MUXn_SEL[3:0] fields. FIR data is stored after being shifted left by 9 bits.
2.2.7
Voltage References
A bandgap circuit provides the reference voltage to the ADC. The amplifier within the reference is chopper
stabilized, i.e., the chopper circuit can be enabled or disabled by the MPU using the I/O RAM control field
CHOP_E[1:0] (I/O RAM 0x2106[3:2]). The two bits in the CHOP_E[1:0] field enable the MPU to operate the
chopper circuit in regular or inverted operation, or in toggling modes (recommended). When the chopper
circuit is toggled in between multiplexer cycles, dc offsets on VREF are automatically be averaged out,
therefore the chopper circuit should always be configured for one of the toggling modes.
Since the VREF band-gap amplifier is chopper-stabilized, the dc offset voltage, which is the most
significant long-term drift mechanism in the voltage references (VREF), is automatically removed by the
chopper circuit. Both the 71M6543 and the 71M6xx3 feature chopper circuits for their respective VREF
voltage reference.
The general topology of a chopped amplifier is shown in Figure 6. The CROSS signal is an internal on-
chip signal and is not accessible on any pin or register.
相關PDF資料 |
PDF描述 |
|---|---|
| 71M6543G-IGT/F | SPECIALTY ANALOG CIRCUIT, PQFP100 |
| 722BG | 2-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| 722MG | 2-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| 73M1903-IGV | SPECIALTY CONSUMER CIRCUIT, PQFP32 |
| 73M1903-IM | SPECIALTY CONSUMER CIRCUIT, QCC32 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 71M6543GHT-IGT/F | 制造商:Maxim Integrated Products 功能描述:3-PHASE, 128KB, PRES TEMP SENSOR, HI PREC - Bulk |
| 71M6543GHT-IGTR/F | 制造商:Maxim Integrated Products 功能描述:3-PHASE, 128KB, PRES TEMP SENSOR, HI PREC - Tape and Reel |
| 71M6543G-IGT/F | 功能描述:計量片上系統 - SoC Precision Energy Meter IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 處理器系列:71M6511 類型:Metering SoC 最大時鐘頻率:70 Hz 程序存儲器大小:64 KB 數據 RAM 大小:7 KB 接口類型:UART 可編程輸入/輸出端數量:12 片上 ADC: 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-64 封裝:Reel |
| 71M6543G-IGTR/F | 功能描述:計量片上系統 - SoC Precision Energy Meter IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 處理器系列:71M6511 類型:Metering SoC 最大時鐘頻率:70 Hz 程序存儲器大小:64 KB 數據 RAM 大小:7 KB 接口類型:UART 可編程輸入/輸出端數量:12 片上 ADC: 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-64 封裝:Reel |
| 71M6543GT-IGT/F | 制造商:Maxim Integrated Products 功能描述:3-PHASE, 128KK, PRES TEMP SENSOR - Bulk |
發布緊急采購，3分鐘左右您將得到回復。