- 您現在的位置：買賣IC網 > PDF目錄68812 > 71M6543GH-IGT/F (MAXIM INTEGRATED PRODUCTS INC) SPECIALTY ANALOG CIRCUIT, PQFP100 PDF資料下載
參數資料
| 型號： | 71M6543GH-IGT/F |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | 模擬信號調理 |
| 英文描述： | SPECIALTY ANALOG CIRCUIT, PQFP100 |
| 封裝： | LEAD FREE, LQFP-100 |
| 文件頁數： | 88/157頁 |
| 文件大小： | 2178K |
| 代理商： | 71M6543GH-IGT/F |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁當前第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁
71M6543F/H and 71M6543G/GH Data Sheet
36
2008–2011 Teridian Semiconductor Corporation
v1.2
The MPU core power consumption can be significantly reduced by the proper use of Idle Mode. The
amount of power saved depends on the percentage of time spent in Idle Mode. Since some interrupts
may occur frequently, thus ending Idle Mode, one method to maximize power savings using Idle Mode, is
to employ a software loop in the main background routine at a point where the MPU background
processing may be permitted to idle. This loop invokes Idle Mode while testing a bit to exit the loop.
Frequently occurring interrupts end Idle Mode, but Idle Mode is immediately re-entered when control is
returned to the idle loop. To exit the idle loop, an interrupt must occur, and the associated interrupt
service routine must set the bit that terminates the idle loop execution.
Power-Down Mode halts the MPU and its peripherals. Power-Down Mode is ended by either a hardware
reset or an external interrupt event. To enter Power-Down Mode, the firmware must set the PD bit (bit 1)
in the PCON SFR register (SFR 0x87).
Table 16. 80515 PCON SFR Register (SFR 0x87)
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
SMOD
-
PD
IDL
Notes:
The SMOD bit is not related to power management.
See 2.4.6 UARTs below for information on the SMOD bit.
2.4.6
UARTs
The 71M6543 include a UART (UART0) that can be programmed to communicate with a variety of AMR
modules and other external devices. A second UART (UART1) is connected to the optical port, as
described in the 2.5.9 UART and Optical Interface on page 57.
The UARTs are dedicated 2-wire serial interfaces, which can communicate with an external host processor
at up to 38,400 bits/s (with MPU clock = 1.2288 MHz). The operation of the RX and TX UART0 pins is as
follows:
UART0 RX: Serial input data are applied at this pin. Conforming to RS-232 standard, the bytes are
input LSB first.
UART0 TX: This pin is used to output the serial data. The bytes are output LSB first.
The 71M6543 has several UART-related registers for the control and buffering of serial data.
A single SFR register serves as both the transmit buffer and receive buffer (S0BUF, SFR 0x99 for UART0
and S1BUF, SFR 0x9C for UART1). When written by the MPU, SxBUF acts as the transmit buffer, and
when read by the MPU, it acts as the receive buffer. Writing data to the transmit buffer starts the
transmission by the associated UART. Received data are available by reading from the receive buffer.
Both UARTs can simultaneously transmit and receive data.
WDCON[7] (SFR 0xD8) selects whether timer 1 or the internal baud rate generator is used. All UART
transfers are programmable for parity enable, parity, 2 stop bits/1 stop bit and XON/XOFF options for
variable communication baud rates from 300 to 38400 bps. Table 17 shows how the baud rates are
calculated. Table 18 shows the selectable UART operation modes.
Table 17: Baud Rate Generation
Using Timer 1
(WDCON[7] = 0)
Using Internal Baud Rate Generator
(WDCON[7] = 1)
UART0
2
smod * f
CKMPU/ (384 * (256-TH1))
2
smod * f
CKMPU/(64 * (2
10-S0REL))
UART1
N/A
fCKMPU/(32 * (2
10-S1REL))
S0REL and S1REL are 10-bit values derived by combining bits from the respective timer reload registers.
(S0RELL, S0RELH, S1RELL, S1RELH are SFR 0xAA, SFR 0xBA, SFR 0x9D and SFR 0xBB, respectively) SMOD
is the SMOD bit in the SFR PCON register (SFR 0x87). TH1 (SFR 0x8D) is the high byte of timer 1.
相關PDF資料 |
PDF描述 |
|---|---|
| 71M6543G-IGT/F | SPECIALTY ANALOG CIRCUIT, PQFP100 |
| 722BG | 2-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| 722MG | 2-OUTPUT DC-DC REG PWR SUPPLY MODULE |
| 73M1903-IGV | SPECIALTY CONSUMER CIRCUIT, PQFP32 |
| 73M1903-IM | SPECIALTY CONSUMER CIRCUIT, QCC32 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 71M6543GHT-IGT/F | 制造商:Maxim Integrated Products 功能描述:3-PHASE, 128KB, PRES TEMP SENSOR, HI PREC - Bulk |
| 71M6543GHT-IGTR/F | 制造商:Maxim Integrated Products 功能描述:3-PHASE, 128KB, PRES TEMP SENSOR, HI PREC - Tape and Reel |
| 71M6543G-IGT/F | 功能描述:計量片上系統 - SoC Precision Energy Meter IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 處理器系列:71M6511 類型:Metering SoC 最大時鐘頻率:70 Hz 程序存儲器大小:64 KB 數據 RAM 大小:7 KB 接口類型:UART 可編程輸入/輸出端數量:12 片上 ADC: 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-64 封裝:Reel |
| 71M6543G-IGTR/F | 功能描述:計量片上系統 - SoC Precision Energy Meter IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 處理器系列:71M6511 類型:Metering SoC 最大時鐘頻率:70 Hz 程序存儲器大小:64 KB 數據 RAM 大小:7 KB 接口類型:UART 可編程輸入/輸出端數量:12 片上 ADC: 安裝風格:SMD/SMT 封裝 / 箱體:LQFP-64 封裝:Reel |
| 71M6543GT-IGT/F | 制造商:Maxim Integrated Products 功能描述:3-PHASE, 128KK, PRES TEMP SENSOR - Bulk |
發布緊急采購，3分鐘左右您將得到回復。