- 您現在的位置：買賣IC網 > PDF目錄24617 > 9161A-01CW16T (INTEGRATED DEVICE TECHNOLOGY INC) 120 MHz, VIDEO CLOCK GENERATOR, PDSO16 PDF資料下載
參數資料
| 型號： | 9161A-01CW16T |
| 廠商： | INTEGRATED DEVICE TECHNOLOGY INC |
| 元件分類： | 時鐘產生/分配 |
| 英文描述： | 120 MHz, VIDEO CLOCK GENERATOR, PDSO16 |
| 封裝： | SOIC-16 |
| 文件頁數： | 11/15頁 |
| 文件大小： | 544K |
| 代理商： | 9161A-01CW16T |
5
ICS9161A
0210I—03/21/05
Serial Programming Architecture
The pins SEL0 and SEL1 perform the dual functions of
select-ing registers and serial programming. In serial
programming mode, SEL0 acts as a clock pin while SEL1
acts as the data pin. The ICS9161A-01 may not be serially
programmed when in power-down mode.
In order to program a particular register, an unlocking
sequence must occur.The unlocking sequence is detailed
in the following timing diagram:
Serial Data Register
The serial data is clocked into the serial data register in the
order described in Figure 1 below (Serial Data Timing).
The serial data is sent as follows: An individual data bit is
sampled on the rising edge of CLK.The complement of the
data bit must be sampled on the previous falling edge of
CLK. The setup and hold time requirements must be met
on both CLK edges. For specifics on timing, see the timing
diagrams on pages 10, 11 and 12.
The bits are shifted in this order: a start bit, 21 data bits,
3 address bits (which designate the desired register), and
a stop bit. A total of 24 bits must always be loaded into the
serial data register or an error is issued. Following the entry
of the last data bit, a stop bit or load command is issued
by bringing DATA high and toggling CLK high-to-low and
low-to-high. The unlocking mechanism then resets itself
following the load. Only after a time-out period are the
SEL0 and SEL1 pins allowed to return to a register
selection function.
Since the VCLK registers are selected by the SEL0 and
SEL1 pins, and since any change in their state may affect
the output frequency, new data input on the selection bits
is only permitted to pass through the decode logic after the
watchdog timer has timed out.This delay of SEL0 or SEL1
data permits a serial program cycle to occur without
affecting the current register selection.
The unlock sequence consists of at least five low-to-high
transitions of CLK while data is high, followed immediately
by a single low-to-high transition while data is low. Following
this unlock sequence, data can be loaded into the serial
data register.This programming must include the start bit,
shown in Figure 1.
Following any transition of CLK or DATA, the watchdog
timer is reset and begins counting. The watchdog timer
ensures that successive rising edges of CLK and DATA do
not violate the time-out specification of 2ms. If a time-out
occurs, the lock mechanism is reset and the data in the
serial data register is ignored.
Figure 1: Serial Data Timing
相關PDF資料 |
PDF描述 |
|---|---|
| 9161A-01CW16LFT | 120 MHz, VIDEO CLOCK GENERATOR, PDSO16 |
| 9161A-01CW16LF | 120 MHz, VIDEO CLOCK GENERATOR, PDSO16 |
| 051-427-3196 | RF Coaxial Connectors |
| 9161A-01CW16WLF | 120 MHz, VIDEO CLOCK GENERATOR, PDSO16 |
| 9161A-01CW16W | 120 MHz, VIDEO CLOCK GENERATOR, PDSO16 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| 9-161A-R | 制造商:Cinch Connectors 功能描述: |
| 9161-CHR-BULK | 制造商:Belden Inc 功能描述: |
| 9-161-L | 制造商:Cinch Connectors 功能描述: |
| 9-161-R | 制造商:Cinch Connectors 功能描述:Conn Terminal Strip 9 POS 11.13mm Crimp ST Cable Mount |
| 9162 | 功能描述:PROTO-BOARD 14/16PIN SOIC SMD RoHS:是 類別:原型開發產品 >> 適配器，可互換接口板 系列:9000, Surfboards® 標準包裝:1 系列:- 原型板類型:- Package Accepted:- 尺寸/尺寸:- 位置數:- 孔直徑:- 板厚度:- 材質:- |
發布緊急采購，3分鐘左右您將得到回復。