- 您現在的位置：買賣IC網 > PDF目錄373914 > AD7706EB (Analog Devices, Inc.) High Performance Switched Capacitor Universal Filter; Package: PDIP; No of Pins: 14; Temperature Range: 0°C to +70°C PDF資料下載
參數資料
| 型號： | AD7706EB |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | High Performance Switched Capacitor Universal Filter; Package: PDIP; No of Pins: 14; Temperature Range: 0°C to +70°C |
| 中文描述： | 3伏/ 5伏1毫瓦2-/3-Channel 16位Σ-Δ模數轉換器（264.12十一） |
| 文件頁數： | 19/32頁 |
| 文件大小： | 264K |
| 代理商： | AD7706EB |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
AD7705/AD7706
–19–
REV. A
Self-Calibration
A self-calibration is initiated on the AD7705/AD7706 by writing
the appropriate values (0, 1) to the MD1 and MD0 bits of
the Setup Register. In the self-calibration mode with a unipo-
lar input range, the zero scale point used in determining the
calibration coefficients is with the inputs of the differential
pair internally shorted on the part (i.e., AIN(+) = AIN(–) =
Internal Bias Voltage in the case of the AD7705 and AIN =
COMMON = Internal Bias voltage on the AD7706). The PGA
is set for the selected gain (as per G1 and G0 bits in the Com-
munications Register) for this zero-scale calibration conversion.
The full-scale calibration conversion is performed at the selected
gain on an internally-generated voltage of V
REF
/Selected Gain.
The duration time for the calibration is 6
×
1/Output Rate. This
is made up of 3
×
1/Output Rate for the zero-scale calibration
and 3
×
1/Output Rate for the full-scale calibration. At this time
the MD1 and MD0 bits in the Setup Register return to 0, 0.
This gives the earliest indication that the calibration sequence is
complete. The
DRDY
line goes high when calibration is initi-
ated and does not return low until there is a valid new word in
the data register. The duration time from the calibration com-
mand being issued to
DRDY
going low is 9
×
1/Output Rate.
This is made up of 3
×
1/Output Rate for the zero-scale calibra-
tion, 3
×
1/Output Rate for the full-scale calibration, 3
×
1/Output
Rate for a conversion on the analog input and some overhead to
correctly set up the coefficients. If
DRDY
is low before (or goes
low during) the calibration command write to the Setup Regis-
ter, it may take up to one modulator cycle (MCLKIN/128)
before
DRDY
goes high to indicate that calibration is in progress.
Therefore,
DRDY
should be ignored for up to one modulator
cycle after the last bit is written to the Setup Register in the
calibration command.
For bipolar input ranges in the self-calibrating mode, the se-
quence is very similar to that just outlined. In this case, the two
points are exactly the same as above but, since the part is config-
ured for bipolar operation, the shorted inputs point is actually
midscale of the transfer function.
System Calibration
System calibration allows the AD7705/AD7706 to compensate
for system gain and offset errors as well as its own internal er-
rors. System calibration performs the same slope factor calcula-
tions as self-calibration, but uses voltage values presented by
the system to the AIN inputs for the zero- and full-scale points.
Full system calibration requires a two-step process, a ZS System
Calibration followed by an FS System Calibration.
For a full system calibration, the zero-scale point must be pre-
sented to the converter first. It must be applied to the converter
before the calibration step is initiated and remain stable until the
step is complete. Once the system zero-scale voltage has been
set up, a ZS System Calibration is then initiated by writing the
appropriate values (1, 0) to the MD1 and MD0 bits of the
Setup Register. The zero-scale system calibration is performed
at the selected gain. The duration of the calibration is 3
×
1/Output
Rate. At this time, the MD1 and MD0 bits in the Setup Register
return to 0, 0. This gives the earliest indication that the calibra-
tion sequence is complete. The
DRDY
line goes high when
calibration is initiated and does not return low until there is a
valid new word in the data register. The duration time from
the calibration command being issued to
DRDY
going low is
4
×
1/Output Rate as the part performs a normal conversion on
the AIN voltage before
DRDY
goes low. If
DRDY
is low before
(or goes low during) the calibration command write to the Setup
Register, it may take up to one modulator cycle (MCLKIN/128)
before
DRDY
goes high to indicate that calibration is in progress.
Therefore,
DRDY
should be ignored for up to one modulator
cycle after the last bit is written to the Setup Register in the
calibration command.
After the zero-scale point is calibrated, the full-scale point is
applied to AIN and the second step of the calibration process is
initiated by again writing the appropriate values (1, 1) to MD1
and MD0. Again, the full-scale voltage must be set up before
the calibration is initiated and it must remain stable throughout
the calibration step. The full-scale system calibration is per-
formed at the selected gain. The duration of the calibration is
3
×
1/Output Rate. At this time, the MD1 and MD0 bits in the
Setup Register return to 0, 0. This gives the earliest indication
that the calibration sequence is complete. The
DRDY
line goes
high when calibration is initiated and does not return low until
there is a valid new word in the data register. The duration time
from the calibration command being issued to
DRDY
going low
is 4
×
1/Output Rate as the part performs a normal conversion
on the AIN voltage before
DRDY
goes low. If
DRDY
is low
before (or goes low during) the calibration command write to
the Setup Register, it may take up to one modulator cycle
(MCLKIN/128) before
DRDY
goes high to indicate that cali-
bration is in progress. Therefore,
DRDY
should be ignored for
up to one modulator cycle after the last bit is written to the
Setup Register in the calibration command.
In the unipolar mode, the system calibration is performed be-
tween the two endpoints of the transfer function; in the bipolar
mode, it is performed between midscale (zero differential volt-
age) and positive full-scale.
The fact that the system calibration is a two-step calibration
offers another feature. After the sequence of a full system cali-
bration has been completed, additional offset or gain calibra-
tions can be performed by themselves to adjust the system zero
reference point or the system gain. Calibrating one of the pa-
rameters, either system offset or system gain, will not affect the
other parameter.
System calibration can also be used to remove any errors from
source impedances on the analog input when the part is used in
unbuffered mode. A simple R, C antialiasing filter on the front
end may introduce a gain error on the analog input voltage, but
the system calibration can be used to remove this error.
Span and Offset Limits
Whenever a system calibration mode is used, there are limits on
the amount of offset and span which can be accommodated.
The overriding requirement in determining the amount of offset
and gain that can be accommodated by the part is the require-
ment that the positive full-scale calibration limit is < 1.05
×
V
REF
/GAIN. This allows the input range to go 5% above the
nominal range. The built-in headroom in the AD7705/AD7706’s
analog modulator ensures that the part will still operate cor-
rectly with a positive full-scale voltage that is 5% beyond the
nominal.
The range of input span in both the unipolar and bipolar modes
has a minimum value of 0.8
×
V
REF
/GAIN and a maximum
value of 2.1
×
V
REF
/GAIN. However, the span (which is the
difference between the bottom of the AD7705/AD7706’s input
相關PDF資料 |
PDF描述 |
|---|---|
| AD7706(中文) | 3 V/5 V, 1 Mw 2-/3-Channel 16-Bit, Sigma-Delta ADCs(三輸入通道16位A/D轉換器) |
| AD7705(中文) | 3 V/5 V, 1 Mw 2-/3-Channel 16-Bit, Sigma-Delta ADCs(完全差分輸入通道16位A/D轉換器) |
| AD7707BR | 3 V/5 V, +-10 V Input Range, 1 mW 3-Channel 16-Bit, Sigma-Delta ADC |
| AD7707BRU | 3 V/5 V, +-10 V Input Range, 1 mW 3-Channel 16-Bit, Sigma-Delta ADC |
| AD7707 | ECONOLINE: REC2.2-S_DR/H1 - 2.2W DIP Package- 1kVDC Isolation- Regulated Output- UL94V-0 Package Material- Continuous Short Circiut Protection- Internal SMD design- 100% Burned In- Efficiency to 75% |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7707 | 制造商:AD 制造商全稱:Analog Devices 功能描述:3 V/5 V, +-10 V Input Range, 1 mW 3-Channel 16-Bit, Sigma-Delta ADC |
| AD7707BR | 功能描述:IC ADC 16BIT 3CH 20-SOIC RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
| AD7707BR-REEL | 制造商:Analog Devices 功能描述:ADC Single Delta-Sigma 500sps 16-bit Serial 20-Pin SOIC W T/R 制造商:Analog Devices 功能描述:ADC SGL DELTA-SIGMA 0.5KSPS 16BIT SERL 20SOIC W - Tape and Reel |
| AD7707BR-REEL7 | 制造商:Analog Devices 功能描述:ADC Single Delta-Sigma 500sps 16-bit Serial 20-Pin SOIC W T/R 制造商:Analog Devices 功能描述:ADC SGL DELTA-SIGMA 0.5KSPS 16BIT SERL 20SOIC W - Tape and Reel |
| AD7707BRU | 功能描述:IC ADC 16BIT 3CH 20-TSSOP RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:12 采樣率（每秒）:300k 數據接口:并聯 轉換器數目:1 功率耗散（最大）:75mW 電壓電源:單電源 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:24-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:24-SOIC 包裝:帶卷 (TR) 輸入數目和類型:1 個單端，單極；1 個單端，雙極 |
發布緊急采購，3分鐘左右您將得到回復。