欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: AD7851AN
廠商: ANALOG DEVICES INC
元件分類: ADC
英文描述: 14-Bit 333 kSPS Serial A/D Converter
中文描述: 1-CH 14-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDIP24
封裝: 0.300 INCH, PLASTIC, MO-095AG, DIP-24
文件頁數: 28/36頁
文件大小: 435K
代理商: AD7851AN
AD7851
–28–
REV. A
SERIAL
INTERFACE
MODE
NO
YES
TRANSFER
DATA
DURING
CONVERSION
APPLY
SYNC
(IF REQUIRED), SCLK, READ
CURRENT CONVERSION RESULT ON DOUT PIN,
AND WRITE ALL 0s ON DIN PIN
WAIT FOR BUSY SIGNAL TO GO LOW
OR WAIT FOR BUSY BIT = 0
APPLY
SYNC
(IF REQUIRED), SCLK, WRITE TO CONTROL
REGISTER SETTING CONVST BIT TO 1, READ CURRENT
CONVERSION RESULT ON DOUT PIN
2, 3
INITIATE
CONVERSION
IN
SOFTWARE
WAIT APPROXIMATELY 200ns
AFTER
CONVST
RISING EDGE
APPLY
SYNC
(IF REQUIRED),
SCLK, READ PREVIOUS CONVERSION
RESULT ON DOUT PIN,
AND WRITE ALL 0s ON DIN PIN
NO
YES
TRANSFER
DATA DURING
CONVERSION
APPLY
SYNC
(IF REQUIRED), SCLK, WRITE TO CONTROL
REGISTER SETTING CONVST BIT TO 1, READ PREVIOUS
CONVERSION RESULT ON DOUT PIN (SEE NOTE)
YES
NO
NOTE:
WHEN USING THE SOFTWARE CONVERSION START AND TRANSFERRING
DATA DURING CONVERSION THE USER MUST ENSURE THE CONTROL
REGISTER WRITE OPERATION EXTENDS BEYOND THE FALLING EDGE OF
BUSY. THE FALLING EDGE OF BUSY RESETS THE CONVST BIT TO 0 AND
ONLY AFTER THIS TIME CAN IT BE REPROGRAMMED TO 1 TO START THE
NEXT CONVERSION.
START
POWER-ON, APPLY CLKIN SIGNAL,
WAIT 150ms FOR AUTOMATIC CALIBRATION
PULSE
CONVST
PIN
WAIT FOR BUSY SIGNAL TO GO
LOW OR WAIT FOR BUSY BIT = 0
Figure 41. Flowchart for Setting Up, Reading, and Writing in Interface Modes 2 and 3
Writing to the AD7851
For accessing the on-chip registers it is necessary to write to the
part. T o enable Serial Interface Mode 1, the user must also write
to the part. Figure 41 through 43 outline flowcharts of how to
configure the AD7851 for each of the different serial interface
modes. T he continuous loops on all diagrams indicate the se-
quence for more than one conversion. T he options of using a
hardware (pulsing the
CONVST
pin) or software (setting the
CONVST bit to 1) conversion start, and reading/writing during
or after conversion are shown in Figures 41 and 42. If the
CONVST
pin is never used then it should be tied to DV
DD
per-
manently. Where reference is made to the BUSY bit equal to a
logic 0, to indicate the end of conversion, the user in this case
would poll the BUSY bit in the status register.
Interface Modes 2 and 3 Configuration
Figure 41 shows the flowchart for configuring the part in Inter-
face Modes 2 and 3. For these interface modes, the read and
write operations take place simultaneously via the serial port.
Writing all 0s ensures that no valid data is written to any of the
registers. When using the software conversion start and transfer-
ring data during conversion, Note must be obeyed.
相關PDF資料
PDF描述
AD7851AR 14-Bit 333 kSPS Serial A/D Converter
AD7851ARS 14-Bit 333 kSPS Serial A/D Converter
AD7851KN 14-Bit 333 kSPS Serial A/D Converter
AD7851KR 14-Bit 333 kSPS Serial A/D Converter
AD7853LARS 3 V to 5 V Single Supply, 200 kSPS 12-Bit Sampling ADCs
相關代理商/技術參數
參數描述
AD7851ANZ 功能描述:IC ADC 14BIT SRL 333KSPS 24-DIP RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 位數:12 采樣率(每秒):3M 數據接口:- 轉換器數目:- 功率耗散(最大):- 電壓電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-23-6 包裝:帶卷 (TR) 輸入數目和類型:-
AD7851AR 制造商:Analog Devices 功能描述:ADC Single SAR 333ksps 14-bit Serial 24-Pin SOIC W 制造商:Rochester Electronics LLC 功能描述:14 BIT SELF CALIBRATION ADC I.C. - Bulk
AD7851AR-REEL 制造商:Analog Devices 功能描述:ADC Single SAR 333ksps 14-bit Serial 24-Pin SOIC W T/R
AD7851ARS 制造商:Analog Devices 功能描述:ADC Single SAR 333ksps 14-bit Serial 24-Pin SSOP 制造商:Analog Devices 功能描述:IC 14-BIT ADC
AD7851ARS-REEL 制造商:Analog Devices 功能描述:ADC Single SAR 333ksps 14-bit Serial 24-Pin SSOP T/R
主站蜘蛛池模板: 平凉市| 纳雍县| 包头市| 贞丰县| 清流县| 格尔木市| 大同市| 桂东县| 绥芬河市| 神农架林区| 浦江县| 泗洪县| 刚察县| 腾冲县| 恩施市| 成安县| 平利县| 溧阳市| 万全县| 吉首市| 曲沃县| 大冶市| 宣威市| 罗城| 增城市| 禄丰县| 剑河县| 南汇区| 民县| 崇仁县| 成都市| 桑植县| 贵南县| 巴南区| 松滋市| 林西县| 岳池县| 禹州市| 化德县| 海伦市| 绥阳县|