- 您現在的位置：買賣IC網 > PDF目錄373925 > AD7898AR-3 (ANALOG DEVICES INC) 5 V, 12-Bit, Serial 220 kSPS ADC in an 8-Lead Package PDF資料下載
參數資料
| 型號： | AD7898AR-3 |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | ADC |
| 英文描述： | 5 V, 12-Bit, Serial 220 kSPS ADC in an 8-Lead Package |
| 中文描述： | 1-CH 12-BIT SUCCESSIVE APPROXIMATION ADC, SERIAL ACCESS, PDSO8 |
| 封裝： | SOIC-8 |
| 文件頁數： | 12/16頁 |
| 文件大小： | 184K |
| 代理商： | AD7898AR-3 |
AD7898
–12–
REV. 0
CS
SCLK
1
5
6
15
SDATA
FOUR LEADING ZEROS
THREE-STATE
t
4
2
3
4
16
t
5
t
3
t
QUIET
t
CONVERT
t
2
THREE-STATE
DB11
DB10
DB9
DB0
t
6
t
7
t
8
14
ZERO
ZERO
ZERO
Z
Figure 8. Serial Interface Timing Diagram Mode 1
Mode 1 Operation
The timing diagram in Figure 8 shows the AD7898 operating in
Mode 1. The serial clock provides the conversion clock and also
controls the transfer of information from the AD7898 during
conversion.
CS
initiates the data transfer and conversion process. The fall-
ing edge of
CS
puts the track-and-hold into hold mode, takes
the bus out of three-state and the analog input is sampled at
this point. The conversion is also initiated at this point and will
require 16 SCLK cycles to complete. On the 14th SCLK falling
edge the track-and-hold will go back into track. On the 16th
SCLK falling edge the SDATA line will go back into three-
state. If the rising edge of
CS
occurs before 16 SCLKs have
elapsed then the conversion will be terminated and the SDATA
line will go back into three-state, otherwise SDATA returns to
three-state on the 16th SCLK falling edge as shown in Figure 8.
Sixteen serial clock cycles are required to perform the conver-
sion process and to access data from the AD7898.
CS
going
low provides the first leading zero to be read in by the micro-
controller or DSP. The remaining data is then clocked out by
subsequent SCLK falling edges beginning with the second lead-
ing zero, thus the first falling clock edge on the serial clock has
the first leading zero provided and also clocks out the second
leading zero. The final bit in the data transfer is valid on the
16th falling edge, having being clocked out on the previous (15th)
falling edge. It is also possible to read in data on each SCLK
rising edge, although the first leading zero will still have to be
read on the first SCLK falling edge after the
CS
falling edge.
Therefore the first rising edge of SCLK after the
CS
falling edge
would provide the second leading zero and the 15th rising SCLK
edge would have DB0 provided if the application requires data
to be read on each rising edge.
Mode Selection
Upon power-up, the default mode of operation of the AD7898
is Mode 0. The part will continue to operate in Mode 0 as out-
lined in the Mode 0 Operation section, provided an SCLK edge
is not applied to the AD7898 during the conversion time and
when
CONVST
is low. If an SCLK edge is applied to the
AD7898 during t
CONVERT
and when
CONVST
is low while in
Mode 0, the part will switch to operate in Mode 1 as shown in
Figure 9. The serial interface will now operate as described in
the Mode 1 operation section. The AD7898 will return to
Mode 0 operation from Mode 1 if
CS
is brought low and then
subsequently high without any SCLK edges provided while
CS
is low (see Figure 10). If any SCLK edges are applied to the
device while
CS
is low when in Mode 1, the part will remain in
Mode 1 and may or may not enter a power-down mode as
determined by the number of SCLKs applied, see Power-Down
Mode section.
If the part is operating in Mode 0 and a glitch occurs on the
SCLK line while
CONVST
is low, the part will enter Mode 1
and the conversion that was initiated by
CONVST
going low
will be terminated. The part will now be operating in Mode 1,
but Mode 0 signals will still be applied from the processor.
When
CS
goes low and no SCLK is applied, the part will revert
back to Mode 0 operation. This avoids accidental changing of
modes due to glitches on the SCLK line.
CONVST
SCLK
CONVERSION
TERMINATES,
AD7898 ENTERS
MODE 1
CONVERSION IS
INITIATED IN
MODE 0
t
1
t
CONVERT
= 3.3 s
Figure 9. Entering Mode 1 from Mode 0
CS
SCLK
AD7898 ENTERS
MODE 0
t
1
Figure 10. Entering Mode 0 from Mode 1
Power-Down Mode
The power-down mode is only accessible when in Mode 1
operation. This mode is intended for use in applications where
slower throughput rates are required; either the ADC is pow-
ered down between each conversion, or a series of conversions
may be performed at a high throughput rate and the ADC is
powered down for a relatively long duration between these
bursts of several conversions. When the AD7898 is in power-
down, all analog circuitry is powered down.
相關PDF資料 |
PDF描述 |
|---|---|
| AD7899 | Evaluation Board for 5V, 12-Bit, Serial 220kSPS ADC in 8-Pin Package |
| AD7904 | 4-Channel, 1 MSPS, 8-/10-/12-Bit ADCs with Sequencer in 16-Lead TSSOP |
| AD7904BRU | 4-Channel, 1 MSPS, 8-/10-/12-Bit ADCs with Sequencer in 16-Lead TSSOP |
| AD7914 | 4-Channel, 1 MSPS, 8-/10-/12-Bit ADCs with Sequencer in 16-Lead TSSOP |
| AD7914BRU | 4-Channel, 1 MSPS, 8-/10-/12-Bit ADCs with Sequencer in 16-Lead TSSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AD7898AR-3REEL | 功能描述:IC ADC 12BIT SRL HS 5V 8-SOIC RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| AD7898AR-3REEL7 | 功能描述:IC ADC 12BIT SRL HS 5V 8-SOIC RoHS:否 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| AD7898ARZ-10 | 功能描述:IC ADC 12BIT SRL HS 5V 8-SOIC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| AD7898ARZ-10REEL | 功能描述:IC ADC 12BIT SRL HS 5V 8-SOIC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 標準包裝:1,000 系列:- 位數:16 采樣率（每秒）:45k 數據接口:串行 轉換器數目:2 功率耗散（最大）:315mW 電壓電源:模擬和數字 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:28-SOIC（0.295"，7.50mm 寬） 供應商設備封裝:28-SOIC W 包裝:帶卷 (TR) 輸入數目和類型:2 個單端，單極 |
| AD7898ARZ-10REEL7 | 功能描述:IC ADC 12BIT SRL HS 5V 8-SOIC RoHS:是 類別:集成電路 (IC) >> 數據采集 - 模數轉換器 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:2,500 系列:- 位數:12 采樣率（每秒）:3M 數據接口:- 轉換器數目:- 功率耗散（最大）:- 電壓電源:- 工作溫度:- 安裝類型:表面貼裝 封裝/外殼:SOT-23-6 供應商設備封裝:SOT-23-6 包裝:帶卷 (TR) 輸入數目和類型:- |
發布緊急采購，3分鐘左右您將得到回復。