欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: AD8343-EVAL
廠商: Analog Devices, Inc.
英文描述: DC-to-2.5 GHz High IP3 Active Mixer
中文描述: DC至2.5GHz的高IP3有源混頻器
文件頁數: 16/27頁
文件大?。?/td> 394K
代理商: AD8343-EVAL
REV. 0
AD8343
–16–
For optimal LO-to-Output isolation it is important not to con-
nect the dc nodes of the emitter bias inductors together in an
attempt to share a single bias resistor. Doing so will cause isola-
tion degradation arising from V
BE
mismatches of the transistors
in the core.
OUTPUT INTERFACE (OUTP, OUTM)
The output of the AD8343 comprises a balanced pair of open-
collector outputs. These should be biased to about the same
voltage as is connected to VPOS (see dc specifications table).
Connecting them to an appreciably higher voltage is likely to
result in conduction of the ESD protection network on signal
peaks, which would cause high distortion levels. On the other
hand, setting the dc level of the outputs too low is also likely to
result in poor device linearity due to collector-base capacitance
modulation or saturation of the core transistors.
Output Matching Considerations
The AD8343 requires a differential load for much the same
reasons that the input needs a differential source to achieve
optimal device performance. In addition, a differential load will
provide the best LO to output isolation and the best input to
output isolation.
At low output frequencies it is usually not appropriate to
arrange a conjugate match between the device output and the
load, even though doing so would maximize the small signal
conversion gain. This is because the output impedance at low
frequencies is quite high (a high resistance in parallel with a
small capacitance). Refer to Figure 12 for a plot of the
differ-
ential
output impedance measured at the device pins. This
data is available in standard file format at the ADI web site
(www.analog.com).
If a matching high impedance load is used, sufficient output
voltage swing will occur to cause output clipping even at rela-
tively low input levels, which constitutes a loss of dynamic range.
The linear range of voltage swing at each output pin is about
±
1 volt from the supply voltage VPOS. A good compromise is to
provide a load impedance of about 500
between the output
pins at the desired output frequency (based on 15 mA to 20 mA
bias current at each input). At output frequencies below 500 MHz,
more output power can be obtained before the onset of gross
clipping by using a lower load impedance; however, both gain
and low order distortion performance will be degraded.
500MHz
1000MHz
1500MHz
2000MHz
50MHz
FREQUENCY (50MHz
2500MHz)
Figure 12. Output Differential Impedance (OUTP, OUTM)
The output load impedance should also be kept reasonably low
at the image frequency to avoid developing appreciable extra
voltage swing, which would again reduce dynamic range.
If maintaining a good output return loss is not required, a 10:1
(impedance) flux-coupled transformer may be used to present a
suitable load to the device and to provide collector bias via a center
tap as shown in Figure 21. At all but the lowest output frequen-
cies it becomes desirable to tune out the output capacitance of
the AD8343 by connecting an inductor between the output pins.
On the other hand, when a good output return loss is desired,
the output may be resistively loaded with a shunt resistance
between the output pins in order to set the real value of output
impedance. With selection of both the transformer
s impedance
ratio and the shunting resistance as required, the desired total
load (~500
) will be achieved while optimizing both signal
transfer and output return loss.
At higher output frequencies the output
conductance
of the
device becomes higher (Figure 12), with the consequence
that above about 900 MHz it
does
become appropriate to
perform a conjugate match between the load and the AD8343
s
output. The device
s own output admittance becomes sufficient
to remove the threat of clipping from excessive voltage swing. Just
as for the input, it may become necessary to perform differential
output impedance measurements on your board layout to effec-
tively develop a good matching network.
Output Biasing Considerations
When the output single-ended-to-differential conversion takes
the form of a transformer whose primary winding is center-
tapped, simply apply VPOS to the tap, preferably through a
ferrite bead in series with the tap in order to avoid a common-
mode instability problem (reference section on Input and Output
Stability Considerations). Refer to Figure 21 for an example of
this network. The collector dc bias voltage should be nominally
equal to the supply voltage applied to Pin 5 (VPOS).
If a 1:1 transmission line balun is used for the output, it will be
necessary to bring in collector bias through separate inductors.
These inductors should be chosen to obtain a high impedance at
the RF frequency, while maintaining a suitable self-resonant
frequency. Refer to Figure 22 for an example of this network.
INPUT AND OUTPUT STABILITY CONSIDERATIONS
The differential configuration of the input and output ports of
the AD8343 raises the need to consider both differential and
common-mode RF stability of the device. Throughout the fol-
lowing stability discussion, common mode will be used to refer
to a signal that is referenced to ground. The equivalent common-
mode impedance will be the value of impedance seen from the
node under discussion to ground. The book
Microwave Tran-
sistor Amplifiers
by Guillermo Gonzalez also has an excellent
section covering stability of amplifiers.
The AD8343 is unconditionally stable for any differential im-
pedance, so device stability need not be considered with respect
to the
differential
terminations. However, the device is potentially
unstable (k factor is less than one) for some common-mode
impedances. Figures 13 and 14 plot the input and output
common-mode stability regions, respectively. Figure 15
shows the test equipment configuration to measure these
stability circles.
相關PDF資料
PDF描述
AD8343ARU DC-to-2.5 GHz High IP3 Active Mixer
AD8343ARU-REEL7 DC-to-2.5 GHz High IP3 Active Mixer
AD8344 Active Receive Mixer 400 MHz to 1.2 GHz
AD8344-EVAL Active Receive Mixer 400 MHz to 1.2 GHz
AD8344ACPZ-REEL7 Active Receive Mixer 400 MHz to 1.2 GHz
相關代理商/技術參數
參數描述
AD8343-EVALZ 制造商:Analog Devices 功能描述:AD8343 EVALUATION BOARD - Bulk
AD8344 制造商:AD 制造商全稱:Analog Devices 功能描述:Active Receive Mixer 400 MHz to 1.2 GHz
AD8344ACPZ 制造商:Analog Devices 功能描述:UP/DOWN CONV MIXER 5V 1.2GHZ 16LFCSP EP - Tape and Reel 制造商:Analog Devices 功能描述:IC SM RF MIXER 800MHZ
AD8344ACPZ 制造商:Analog Devices 功能描述:IC RF MIXER 800MHZ SMD LFCSP-16
AD8344ACPZ-REEL7 功能描述:IC MIXER 400MHZ-1.2GHZ 16-LFCSP RoHS:是 類別:RF/IF 和 RFID >> RF 混頻器 系列:AD8344 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:100 系列:- RF 型:W-CDMA 頻率:2.11GHz ~ 2.17GHz 混頻器數目:1 增益:17dB 噪音數據:2.2dB 次要屬性:- 電流 - 電源:11.7mA 電源電壓:2.7 V ~ 3.3 V 包裝:托盤 封裝/外殼:12-VFQFN 裸露焊盤 供應商設備封裝:12-QFN-EP(3x3)
主站蜘蛛池模板: 淳化县| 阳山县| 宣威市| 横峰县| 南昌市| 甘肃省| 大同县| 怀化市| 理塘县| 南平市| 遵义市| 上犹县| 巴南区| 太谷县| 鸡东县| 荃湾区| 南漳县| 汶川县| 普格县| 乌兰察布市| 梨树县| 安福县| 桐庐县| 通江县| 青浦区| 周口市| 昔阳县| 海城市| 城固县| 长子县| 安康市| 阳新县| 乌鲁木齐县| 南宁市| 资溪县| 西充县| 牙克石市| 锦屏县| 通道| 铜山县| 彭阳县|