欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: AD9822JRS
廠商: ANALOG DEVICES INC
元件分類: 消費家電
英文描述: Complete 14-Bit CCD/CIS Signal Processor
中文描述: SPECIALTY CONSUMER CIRCUIT, PDSO28
封裝: 5.30 MM, SSOP-28
文件頁數: 9/15頁
文件大小: 150K
代理商: AD9822JRS
REV. A
AD9822
–9–
FUNCTIONAL DESCRIPTION
The AD9822 can be operated in four different modes: 3-Channel
CDS Mode, 3-Channel SHA Mode, 1-Channel CDS Mode,
and 1-Channel SHA Mode. Each mode is selected by program-
ming the Configuration Register through the serial interface.
For more detail on CDS or SHA mode operation, see the
Circuit
Operation section.
3-Channel CDS Mode
In 3-Channel CDS Mode, the AD9822 simultaneously samples
the red, green and blue input voltages from the CCD outputs.
The sampling points for each Correlated Double Sampler (CDS)
are controlled by CDSCLK1 and CDSCLK2 (see Figures 8 and
9). CDSCLK1’s falling edge samples the reference level of the
CCD waveform. CDSCLK2’s falling edge samples the data
level of the CCD waveform. Each CDS amplifier outputs the
difference between the CCD’s reference and data levels. Next,
the output voltage of each CDS amplifier is level-shifted by an
Offset DAC. The voltages are then scaled by the three Program-
mable Gain Amplifiers before being multiplexed through the
14-bit ADC. The ADC sequentially samples the PGA outputs
on the falling edges of ADCCLK.
The offset and gain values for the red, green and blue channels
are programmed using the serial interface. The order in which
the channels are switched through the multiplexer is selected by
programming the MUX register.
Timing for this mode is shown in Figure 1. It is recommended
that the falling edge of CDSCLK2 occur coincident with or before
the rising edge of ADCCLK, although this is not required
to satisfy the minimum timing constraints. The rising edge of
CDSCLK2 should not occur before the previous falling edge of
ADCCLK, as shown by t
ADC2
. The output data latency is three
clock cycles.
3-Channel SHA Mode
In 3-Channel SHA Mode, the AD9822 simultaneously samples
the red, green and blue input voltages. The sampling point is
controlled by CDSCLK2. CDSCLK2’s falling edge samples the
input waveforms on each channel. The output voltages from the
three SHAs are modified by the offset DACs and then scaled by
the three PGAs. The outputs of the PGAs are then multiplexed
through the 14-bit ADC. The ADC sequentially samples the
PGA outputs on the falling edges of ADCCLK.
The input signal is sampled with respect to the voltage applied
to the OFFSET pin (see Figure 10). With the OFFSET pin
grounded, a zero volt input corresponds to the ADC’s zero-scale
output. The OFFSET pin may also be used as a coarse offset
adjust pin. A voltage applied to this pin will be subtracted from
the voltages applied to the red, green, and blue inputs in the
first amplifier stage of the AD9822. The input clamp is dis-
abled in this mode. For more information, see the Circuit
Operation section.
Timing for this mode is shown in Figure 2. CDSCLK1 should
be grounded in this mode. Although not required, it is recom-
mended that the falling edge of CDSCLK2 occur coincident
with or before the rising edge of ADCCLK. The rising edge of
CDSCLK2 should not occur before the previous falling edge of
ADCCLK, as shown by t
ADC2
. The output data latency is three
ADCCLK cycles.
The offset and gain values for the red, green, and blue channels
are programmed using the serial interface. The order in which
the channels are switched through the multiplexer is selected by
programming the MUX register.
1-Channel CDS Mode
This mode operates in the same way as the 3-Channel CDS
mode. The difference is that the multiplexer remains fixed in
this mode, so only the channel specified in the MUX register is
processed.
Timing for this mode is shown in Figure 3.
1-Channel SHA Mode
This mode operates in the same way as the 3-Channel SHA
mode, except that the multiplexer remains stationary. Only the
channel specified in the MUX register is processed.
The input signal is sampled with respect to the voltage applied
to the OFFSET pin. With the OFFSET pin grounded, a zero
volt input corresponds to the ADC’s zero scale output. The
OFFSET pin may also be used as a coarse offset adjust pin. A
voltage applied to this pin will be subtracted from the voltages
applied to the red, green, and blue inputs in the first amplifier
stage of the AD9822. The input clamp is disabled in this mode.
For more information, see the Circuit Operation section.
Timing for this mode is shown in Figure 4. CDSCLK1 should
be grounded in this mode of operation.
相關PDF資料
PDF描述
AD9823 Correlated Double Sampler (CDS)
AD9823BRUZ Correlated Double Sampler (CDS)
AD9824KCP Complete 14-Bit 30 MSPS CCD Signal Processor
AD9824 Complete 14-Bit 30 MSPS CCD Signal Processor
AD9826KRS Complete 16-Bit Imaging Signal Processor
相關代理商/技術參數
參數描述
AD9822JRSRL 制造商:Analog Devices 功能描述:AFE Video 1ADC 14-Bit 5V 28-Pin SSOP T/R 制造商:Rochester Electronics LLC 功能描述:14 BIT AFE WITH 12 BIT LINEARITY - Bulk
AD9822JRSZ 功能描述:IC CCD SIGNAL PROC 14BIT 28SSOP RoHS:是 類別:集成電路 (IC) >> 接口 - 傳感器和探測器接口 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:74 系列:- 類型:觸控式傳感器 輸入類型:數字 輸出類型:數字 接口:JTAG,串行 電流 - 電源:100µA 安裝類型:表面貼裝 封裝/外殼:20-TSSOP(0.173",4.40mm 寬) 供應商設備封裝:20-TSSOP 包裝:管件
AD9822JRSZRL 功能描述:IC CCD SIGNAL PROC 14BIT 28SSOP RoHS:是 類別:集成電路 (IC) >> 接口 - 傳感器和探測器接口 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:74 系列:- 類型:觸控式傳感器 輸入類型:數字 輸出類型:數字 接口:JTAG,串行 電流 - 電源:100µA 安裝類型:表面貼裝 封裝/外殼:20-TSSOP(0.173",4.40mm 寬) 供應商設備封裝:20-TSSOP 包裝:管件
AD9822JRZ 制造商:Analog Devices 功能描述:AFE Video 1ADC 14-Bit 5V 28-Pin SOIC W
AD9822JRZRL 制造商:Analog Devices 功能描述:AFE Video 1ADC 14-Bit 5V 28-Pin SOIC W T/R
主站蜘蛛池模板: 镇安县| 黑水县| 项城市| 沭阳县| 武冈市| 县级市| 奉节县| 古蔺县| 饶平县| 安泽县| 关岭| 嘉禾县| 阳信县| 建平县| 泽库县| 长兴县| 桂林市| 静宁县| 商都县| 监利县| 饶平县| 姚安县| 昔阳县| 乌审旗| 射阳县| 泰顺县| 安化县| 五大连池市| 英吉沙县| 台中市| 怀宁县| 古蔺县| 余姚市| 麻阳| 阜新| 龙陵县| 衢州市| 翼城县| 汕头市| 五原县| 定陶县|