- 您現在的位置：買賣IC網 > PDF目錄373995 > ADM1022 (Analog Devices, Inc.) Low-Cost PC Temperature Monitor and Fan Control ASIC PDF資料下載
參數資料
| 型號： | ADM1022 |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | Low-Cost PC Temperature Monitor and Fan Control ASIC |
| 中文描述： | 低價電腦溫度監控和風扇控制ASIC |
| 文件頁數： | 5/19頁 |
| 文件大?。?/td> | 190K |
| 代理商： | ADM1022 |
第1頁第2頁第3頁第4頁當前第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁
REV. 0
ADM1022
–5–
PIN FUNCTION DESCRIPTION
Pin
No.
Mnemonic
Description
1
FAN_OFF
Digital Output (Open-Drain) Fan Off Request. When asserted low this indicates a request to shut
off the fan independent of the FAN_SPD output. When negated (output FET off) it indicates that
the fan may be turned on.
Digital Input, Manual Reset. A logic low on this input causes
RST2
to be asserted. Once this input
is negated that output will remain asserted for t
RP
. This input has an internal 20 k
pull-up resistor.
Leave unconnected if not used.
Digital I/O (Open-Drain). This pin is asserted low while V
CC
remains below the reset threshold. It
remains asserted for t
RP
after the reset condition is terminated. It is bidirectional so the ADM1022 can
be optionally reset; external logic must be used to prevent system auxiliary reset from occurring
when used as an input.
GROUND. Power and Signal Ground.
POWER 3.3 V. Power source and voltage monitor input for first reset generator.
Analog Input. Voltage monitor input for second reset generator.
Digital Output (Open-Drain). This pin is asserted low under any of the following conditions:
– V
MON
or V
CC
remains below the reset threshold
– while
MR
is held low
– while
RST1
is asserted.
It remains asserted for t
RP
after the reset conditions are terminated.
Analog Output/Test Input. An active-high input that enables NAND board-level connectivity testing.
Refer to section on NAND testing. Used as an analog output for fan speed control when NAND
test is not selected.
Remote Thermal Diode Negative Input. This is the negative input (current sink) from the remote
thermal diode. This also serves as the negative input into the A/D.
Remote Thermal Diode Positive Input. This is the positive input (current source) from the remote
thermal diode. This serves as the positive input into the A/D.
Analog Input/Digital I/O (Open-Drain). Can be programmed as negative input for a second diode
temperature sensor, or as a digital I/O pin. In this case it is an active low thermal overload output
that indicates a violation of a temperature set point (over-temperature). Also acts as an input to
provide external fan control. When this pin is pulled low by an external signal, a status bit is set and
the fan speed is set to full on.
Analog/Digital Input. Can be programmed as the positive input for a second diode sensor, or as a
general-purpose logic input. In this case it can be programmed as an active high or active low input
that sets Bit 4 of the Status Registers. This bit can only be reset by reading the status registers, pro-
vided GPI is in the inactive state.
Digital I/O. The lowest order programmable bit of the SMBus Address. ADD is sampled at power-
up and changing it while powered on will have no immediate effect. This pin also functions as an
output when doing a NAND test.
Digital Output (Open Drain), System Interrupt Output. This signal indicates a violation of a set
trip point. The output is enabled when Bit 1 of the Configuration Register is set to 1. The default
state is disabled.
Digital Input SMBus Clock.
Digital I/O (Open-Drain) SMBus Bidirectional Data.
2
MR
3
RST1
4
5
6
7
GND
V
CC
V
MON
RST2
8
FAN_SPD/NTEST_IN
9
D1–
10
D1+
11
D2–/
THERM
12
D2+/GPI
13
ADD/NTEST_OUT
14
INT
15
16
SCL
SDA
相關PDF資料 |
PDF描述 |
|---|---|
| ADM1022ARQ | Low-Cost PC Temperature Monitor and Fan Control ASIC |
| ADM1023 | LJT 6C 6#12 PIN PLUG |
| ADM1023ARQ | ACPI-Compliant High-Accuracy Microprocessor System Temperature Monitor |
| ADM1024 | System Hardware Monitor with Remote Diode Thermal Sensing |
| ADM1024ARU | Circular Connector; No. of Contacts:8; Series:LJT06R; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:17; Circular Contact Gender:Pin; Circular Shell Style:Straight Plug; Insert Arrangement:17-8 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADM102-22/12VDC | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC |
| ADM102-22/24VDC | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC |
| ADM102-22/48VDC | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC |
| ADM1022ARQ | 制造商:ON Semiconductor 功能描述:Temp Sensor Analog 16-Pin QSOP 制造商:Rochester Electronics LLC 功能描述:THERMAL MONITOR AND CONTROLER I.C. - Bulk |
| ADM1022ARQ-REEL | 功能描述:IC SENSOR TEMP/DET 3/5.5V 16QSOP RoHS:否 類別:集成電路 (IC) >> 接口 - 傳感器和探測器接口 系列:- 其它有關文件:Automotive Product Guide 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:74 系列:- 類型:觸控式傳感器 輸入類型:數字 輸出類型:數字 接口:JTAG，串行 電流 - 電源:100µA 安裝類型:表面貼裝 封裝/外殼:20-TSSOP（0.173"，4.40mm 寬） 供應商設備封裝:20-TSSOP 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。