欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: ADM1024ARU
廠商: ANALOG DEVICES INC
元件分類: 電源管理
英文描述: Circular Connector; No. of Contacts:8; Series:LJT06R; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:17; Circular Contact Gender:Pin; Circular Shell Style:Straight Plug; Insert Arrangement:17-8
中文描述: 9-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO24
封裝: MO-153AD, TSSOP-24
文件頁數: 15/28頁
文件大小: 285K
代理商: ADM1024ARU
ADM1024
–15–
REV. 0
6. In all these circuits, the output transistor must have an I
CMAX
greater than the maximum fan current, and be capable of
dissipating power due to the voltage dropped across it when
the fan is not operating at full speed.
7. If the fan motor produces a large back e.m.f when switched
off, it may be necessary to add clamp diodes to protect the
output transistors in the event that the output goes very
quickly from full scale to zero.
FAULT-TOLERANT FAN CONTROL
The ADM1024 incorporates a fault-tolerant fan control capability
that can override the setting of the analog output and force it to
maximum to give full fan speed in the event of a critical over-
temperature problem even if, for some reason, this has not been
handled by the system software.
There are four temperature set points that will force the analog
output to FFh if any one of them is exceeded for three or more
consecutive measurements. Two of these limits are programmable
by the user and two are hardware limits intended as
must not exceed
limits that cannot be changed.
The analog output will be forced to FFh if:
The temperature measured by the on-chip sensor exceeds the limit
programmed into register address 13h.
or
The temperature measured by either of the remote sensors exceeds
the limit programmed into address 14h.
or
The temperature measured by the on-chip sensor exceeds 70
°
C,
which is hardware programmed into a read-only register at
address 17h.
or
The temperature measured by either of the remote sensors exceeds
85
°
C, which is hardware programmed into a read-only register
at address 18h.
Once the hardware override of the analog output is triggered,
it will only return to normal operation after three consecutive
measurements that are 5 degrees lower than each of the above
limits.
The analog output can also be forced to FFh by pulling the
THERM
pin (Pin 2) low.
The limits in registers 13h and 14h can be programmed by the
user. Obviously these limits should not exceed the hardware values
in registers 17h and 18h, as they would have no effect. The power-
on default values of these registers are the same as the two
hardware registers, 70
°
C and 85
°
C respectively, so there is no
need to program them if these limits are acceptable.
Once these registers have been programmed, or if the defaults
are acceptable, the values in these registers can be locked by
writing a 1 to Bits 1 and 2 of Configuration Register 2 (address
4Ah). This prevents any unauthorized tampering with the limits.
These lock bits can only be written to 1 and can only be cleared
by power-on reset or by taking the
RESET
pin low, so registers
13h and 14h cannot be written to again unless the device is
powered off, then on.
LAYOUT AND GROUNDING
Analog inputs will provide best accuracy when referred to a clean
ground. A separate, low-impedance ground plane for analog
ground, which provides a ground point for the voltage dividers
and analog components, will provide best performance but is
not mandatory.
The power supply bypass, the parallel combination of 10
μ
F
(electrolytic or tantalum) and 0.1
μ
F (ceramic) bypass capacitors
connected between Pin 9 and ground, should also be located as
close as possible to the ADM1024.
FAN INPUTS
Pins 5 and 6 may be configured as analog inputs or fan speed
inputs by programming Bits 0 and 1 of the Channel Mode
Register. The power-on default for these bits is all zeroes, which
makes Pins 5 and 6 fan inputs.
Signal conditioning in the ADM1024 accommodates the slow
rise and fall times typical of fan tachometer outputs. The
maximum input signal range is 0 to V
CC
. In the event that these
inputs are supplied from fan outputs that exceed 0 V to 6.5 V,
either resistive attenuation of the fan signal or diode clamping
must be included to keep inputs within an acceptable range.
Figures 17a to 17d show circuits for most common fan tach
outputs.
If the fan tach output has a resistive pull-up to V
CC
it can be directly
connected to the fan input, as shown in Figure 17a.
12V
PULL-UP
4.7k
TYP
TACHO
OUTPUT
FAN1 OR
FAN2
V
CC
FAN SPEED
COUNTER
160k
Figure 17a. Fan with Tach. Pull-Up to +V
CC
If the fan output has a resistive pull-up to 12 V (or other voltage
greater than 6.5 V), the fan output can be clamped with a Zener
diode, as shown in Figure 17b. The Zener voltage should be
chosen so it is greater than V
IH
but less than 6.5 V, allowing
for the voltage tolerance of the Zener. A value of between 3 V
and 5 V is suitable.
ZD1*
ZENER
*CHOOSE ZD1 VOLTAGE APPROX. 0.8 V
CC
12V
PULL-UP
4.7k
TYP
TACHO
OUTPUT
FAN1 OR
FAN2
V
CC
FAN SPEED
COUNTER
160k
Figure 17b. Fan with Tach. Pull-Up to Voltage >6.5 V
(e.g., 12 V ) Clamped with Zener Diode
相關PDF資料
PDF描述
ADM1025 Circular Connector; No. of Contacts:8; Series:LJT06R; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:17; Circular Contact Gender:Pin; Circular Shell Style:Straight Plug; Insert Arrangement:17-8
ADM1025A Circular Connector; No. of Contacts:8; Series:LJT06R; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:17; Circular Contact Gender:Socket; Circular Shell Style:Straight Plug; Insert Arrangement:17-8
ADM1025AARQ Low-Cost PC Hardware Monitor ASIC
ADM1025ARQ Low-Cost PC Hardware Monitor ASIC
ADM1026 Complete Thermal and System Management Controller
相關代理商/技術參數
參數描述
ADM1024ARU-REEL 功能描述:IC MONITOR SYS TEMP/VOLT 24TSSOP RoHS:否 類別:集成電路 (IC) >> 接口 - 專用 系列:- 標準包裝:3,000 系列:- 應用:PDA,便攜式音頻/視頻,智能電話 接口:I²C,2 線串口 電源電壓:1.65 V ~ 3.6 V 封裝/外殼:24-WQFN 裸露焊盤 供應商設備封裝:24-QFN 裸露焊盤(4x4) 包裝:帶卷 (TR) 安裝類型:表面貼裝 產品目錄頁面:1015 (CN2011-ZH PDF) 其它名稱:296-25223-2
ADM1024ARUZ 功能描述:馬達/運動/點火控制器和驅動器 THERMAL & VOLT MONITOR IC RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube
ADM1024ARUZ-R7 功能描述:板上安裝溫度傳感器 +/-2 C / +/-3 C Digital RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
ADM1024ARUZ-REEL 功能描述:板上安裝溫度傳感器 THERMAL & VOLT MONITOR IC RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor
ADM1024ARUZ-REEL7 功能描述:IC MONITOR SYS TEMP/VOLT 24TSSOP RoHS:是 類別:集成電路 (IC) >> 接口 - 專用 系列:- 標準包裝:3,000 系列:- 應用:PDA,便攜式音頻/視頻,智能電話 接口:I²C,2 線串口 電源電壓:1.65 V ~ 3.6 V 封裝/外殼:24-WQFN 裸露焊盤 供應商設備封裝:24-QFN 裸露焊盤(4x4) 包裝:帶卷 (TR) 安裝類型:表面貼裝 產品目錄頁面:1015 (CN2011-ZH PDF) 其它名稱:296-25223-2
主站蜘蛛池模板: 海阳市| 桦南县| 库尔勒市| 常德市| 瑞丽市| 伽师县| 大竹县| 永德县| 应城市| 尉氏县| 鄯善县| 吴川市| 太原市| 凤庆县| 黄大仙区| 安庆市| 旬邑县| 深泽县| 汝南县| 阿克苏市| 化州市| 丹寨县| 吉木乃县| 澄城县| 昆明市| 巧家县| 民权县| 北海市| 龙山县| 湘乡市| 临清市| 拜泉县| 阿拉善盟| 光山县| 西青区| 新晃| 凤阳县| 沿河| 响水县| 霍林郭勒市| 仪征市|