- 您現在的位置：買賣IC網 > PDF目錄373995 > ADM1024ARU (ANALOG DEVICES INC) Circular Connector; No. of Contacts:8; Series:LJT06R; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:17; Circular Contact Gender:Pin; Circular Shell Style:Straight Plug; Insert Arrangement:17-8 PDF資料下載
參數資料
| 型號： | ADM1024ARU |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 電源管理 |
| 英文描述： | Circular Connector; No. of Contacts:8; Series:LJT06R; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:17; Circular Contact Gender:Pin; Circular Shell Style:Straight Plug; Insert Arrangement:17-8 |
| 中文描述： | 9-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO24 |
| 封裝： | MO-153AD, TSSOP-24 |
| 文件頁數： | 17/28頁 |
| 文件大小： | 285K |
| 代理商： | ADM1024ARU |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
ADM1024
–17–
REV. 0
measurement. Therefore, if the start of a fan measurement just
misses a rising edge, the measurement can take almost three tach
periods. In order to read a valid result from the fan value registers,
the total monitoring time allowed after starting the monitor-
ing cycle should, therefore, be three tach periods of FAN1 plus
three tach periods of FAN2 at the lowest normal fan speed.
Although the fan monitoring cycle and the analog input monitoring
cycle are started together, they are not synchronized in any
other way.
FAN MANUFACTURERS
Manufacturers of cooling fans with tachometer outputs are
listed below:
NMB Tech
9730 Independence Ave.
Chatsworth, California 91311
Phone: 818-341-3355; Fax: 818-341-8207
Airflow
CFM
Model
Frame Size
2.36 in sq.
×
0.79 in (60 mm sq.
×
20 mm)
2410ML 2.36 in sq.
×
0.98 in (60 mm sq.
×
25 mm) 14–25
3108NL
3.15 in sq.
×
0.79 in (80 mm sq.
×
20 mm) 25–42
3110KL
3.15 in sq.
×
0.98 in (80 mm sq.
×
25 mm) 25–40
2408NL
9–16
Mechatronics Inc.
P.O. Box 613
Preston, WA 98050
800-453-4569
Models—Various sizes available with tach output option.
Sanyo Denki, America, Inc.
468 Amapola Avenue
Torrance, CA 90501
310-783-5400
Models—109P Series
CHASSIS INTRUSION INPUT
The Chassis Intrusion input is an active high input/open-drain
output intended for detection and signalling of unauthorized
tampering with the system. An external circuit powered from
the system’s CMOS backup battery is used to detect and latch a
chassis intrusion event, whether or not the system is powered
up. Once a chassis intrusion has been detected and latched, the
CI input will generate an interrupt when the system is powered up.
The actual detection of chassis intrusion is performed by an
external circuit that will, for example, detect when the cover
has been removed. A wide variety of techniques may be used for
the detection, for example:
Microswitch that opens or closes when the cover is removed.
Reed switch operated by magnet fixed to the cover.
Hall-effect switch operated by magnet fixed to the cover.
Phototransistor that detects light when cover is removed.
The chassis intrusion interrupt will remain asserted until the
external detection circuit is reset. This can be achieved by setting
Bit 7 of the Chassis Intrusion Clear Register to one, which will
cause the CI pin to be pulled low for at least 20 ms. This regis-
ter bit is self-clearing.
The chassis intrusion circuit should be designed so that it can be
reset by pulling its output low. A suitable chassis intrusion circuit
using a phototransistor is shown in Figure 19. Light falling on
the phototransistor when the PC cover is removed will cause it
to turn on and pull up the input of N1, thus setting the latch
N3/N4. After the cover is replaced, a low reset on the CI output
will pull down the input of N4, resetting the latch.
74HC132
100k
10k
CI
MRD901
470k
1N914
CMOS
BACKUP
BATTERY
5V
1N914
N1
N2
N3
N4
Figure 19. Chassis Intrusion Detector and Latch
The Chassis Intrusion input can also be used for other types of
alarm input. Figure 20 shows a temperature alarm circuit using
an AD22105 temperature switch sensor. This produces a low-
going output when the preset temperature is exceeded, so the
output is inverted by Q1 to make it compatible with the CI input.
Q1 can by almost any small-signal NPN transistor, or a TTL
or CMOS inverter gate may be used if one is available. See the
AD22105 data sheet for information on selecting R
SET
.
CI
AD22105
TEMPERATURE
SENSOR
V
CC
R1
10k
R
SET
Q1
Figure 20. Using the CI Input with a Temperature Sensor
Note: The chassis intrusion input does not have a protective
clamp diode to V
CC
, as this could pull down the chassis intru-
sion latch and reset it when the ADM1024 was powered down.
THE ADM1024 INTERRUPT STRUCTURE
The Interrupt Structure of the ADM1024 is shown in Figure 21.
As each measurement value is obtained and stored in the
appropriate value register, the value and the limits from the
corresponding limit registers are fed to the high and low limit
comparators. The result of each comparison (1 = out of limit,
0 = in limit) is routed to the corresponding bit input of the
Interrupt Status Registers via a data demultiplexer, and used to
set that bit high or low as appropriate.
The Interrupt Mask Registers have bits corresponding to each of
the Interrupt Status Register Bits. Setting an Interrupt Mask Bit
high forces the corresponding Status Bit output low, while setting
an Interrupt Mask Bit low allows the corresponding Status Bit
相關PDF資料 |
PDF描述 |
|---|---|
| ADM1025 | Circular Connector; No. of Contacts:8; Series:LJT06R; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:17; Circular Contact Gender:Pin; Circular Shell Style:Straight Plug; Insert Arrangement:17-8 |
| ADM1025A | Circular Connector; No. of Contacts:8; Series:LJT06R; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:17; Circular Contact Gender:Socket; Circular Shell Style:Straight Plug; Insert Arrangement:17-8 |
| ADM1025AARQ | Low-Cost PC Hardware Monitor ASIC |
| ADM1025ARQ | Low-Cost PC Hardware Monitor ASIC |
| ADM1026 | Complete Thermal and System Management Controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADM1024ARU-REEL | 功能描述:IC MONITOR SYS TEMP/VOLT 24TSSOP RoHS:否 類別:集成電路 (IC) >> 接口 - 專用 系列:- 標準包裝:3,000 系列:- 應用:PDA，便攜式音頻/視頻，智能電話 接口:I²C，2 線串口 電源電壓:1.65 V ~ 3.6 V 封裝/外殼:24-WQFN 裸露焊盤 供應商設備封裝:24-QFN 裸露焊盤（4x4） 包裝:帶卷 (TR) 安裝類型:表面貼裝 產品目錄頁面:1015 (CN2011-ZH PDF) 其它名稱:296-25223-2 |
| ADM1024ARUZ | 功能描述:馬達/運動/點火控制器和驅動器 THERMAL & VOLT MONITOR IC RoHS:否 制造商:STMicroelectronics 產品:Stepper Motor Controllers / Drivers 類型:2 Phase Stepper Motor Driver 工作電源電壓:8 V to 45 V 電源電流:0.5 mA 工作溫度:- 25 C to + 125 C 安裝風格:SMD/SMT 封裝 / 箱體:HTSSOP-28 封裝:Tube |
| ADM1024ARUZ-R7 | 功能描述:板上安裝溫度傳感器 +/-2 C / +/-3 C Digital RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| ADM1024ARUZ-REEL | 功能描述:板上安裝溫度傳感器 THERMAL & VOLT MONITOR IC RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| ADM1024ARUZ-REEL7 | 功能描述:IC MONITOR SYS TEMP/VOLT 24TSSOP RoHS:是 類別:集成電路 (IC) >> 接口 - 專用 系列:- 標準包裝:3,000 系列:- 應用:PDA，便攜式音頻/視頻，智能電話 接口:I²C，2 線串口 電源電壓:1.65 V ~ 3.6 V 封裝/外殼:24-WQFN 裸露焊盤 供應商設備封裝:24-QFN 裸露焊盤（4x4） 包裝:帶卷 (TR) 安裝類型:表面貼裝 產品目錄頁面:1015 (CN2011-ZH PDF) 其它名稱:296-25223-2 |
發布緊急采購，3分鐘左右您將得到回復。