- 您現在的位置：買賣IC網 > PDF目錄373995 > ADM1026 (Analog Devices, Inc.) Complete Thermal and System Management Controller PDF資料下載
參數資料
| 型號： | ADM1026 |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | Complete Thermal and System Management Controller |
| 中文描述： | 完整的熱和系統管理控制器 |
| 文件頁數： | 28/56頁 |
| 文件大小： | 634K |
| 代理商： | ADM1026 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁當前第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁
ADM1026
ADM1026 Interrupt Structure
The Interrupt Structure of the ADM1026 is shown in Figure 53.
Interrupts can come from a number of sources, which are com-
bined to form a common INT output. When INT is asserted,
this output pulls low. The INT pin has an internal, 100 k
pull-up resistor.
Rev. A | Page 28 of 56
Analog/Temperature Inputs
As each analog measurement value is obtained and stored in the
appropriate value register, the value and the limits from the
corresponding limit registers are fed to the high and low limit
comparators. The device performs greater than comparisons to
the high limits. An out-of-limit is also generated if a result is
less than or equal to a low limit. The result of each comparison
(1 = out of limit, 0 = in limit) is routed to the corresponding
bit input of Interrupt Status Register 1, 2, or 4 via a data
demultiplexer, and used to set that bit high or low as appro-
priate. Status bits are self-clearing. If a bit in a status register is
set due to an out-of-limit measurement, it continues to cause
INT to be asserted as long as it remains set, as described later.
However, if a subsequent measurement is in limit, it is reset and
does not cause INT to be reasserted. Status bits are unaffected
by clearing the interrupt.
Interrupt Mask Registers 1, 2, and 4 have bits corresponding to
each of the interrupt status register bits. Setting an interrupt
mask bit high conceals an asserted status bit from display on
Interrupt Pin 17. Setting an interrupt mask bit low allows the
corresponding status bit to be asserted and displayed on Pin 17.
After mask gating, the status bits are all OR’ed together to
produce the analog and fan interrupt that is used to set a latch.
The output of this latch is OR’ed with other interrupt sources to
produce the INT output. This pulls low if any unmasked status
bit goes high, that is, when any measured value goes out of limit.
When an INT output caused by an out-of-limit analog/
temperature measurement is cleared by one of the methods
described later, the latch is reset. It is not set again, and INT is
not reasserted until after two local temperature measure-ments
have been taken, even if the status bit remains set or a new
analog/temperature event occurs, as shown in Figure 50. This
delay corresponds to almost two monitoring cycles, and is about
530 ms. However, interrupts from other sources such as a fan or
GPIO can still occur. This is illustrated in Figure 51.
START OF ANALOG
MONITORING
CYCLE
OUT-OF-LIMIT
MEASUREMENT
START OF ANALOG
MONITORING
CYCLE
INT
INT CLEARED
LOCAL
TEMPERATURE
MEASUREMENT
START OF ANALOG
MONITORING
CYCLE
INT RE-ASSERTED
OUT-OF-LIMIT
MEASUREMENT
FULL MONITORING CYCLE = 273ms
MEASUREMENT
TEMPERATURE
0
Figure 50. Delay After Clearing INT Before Reassertion
START OF ANALOG
MONITORING CYCLE
OUT-OF-LIMIT
MEASUREMENT
LOCAL TEMPEREATURE
MEASUREMENT
START OF ANALOG
MONITORING CYCLE
LOCAL TEMPERATURE
MEASUREMENT
START OF ANALOG
MONITORING CYCLE
INT
CLEARED
INT RE-ASSERTED
NEW INT
FROM FAN
NEW
INT
FROM GPIO
GPIO DE-ASSERTED
INT
INT
CLEARED
0
Figure 51. Other Interrupt Sources Can Reassert INT Immediately
相關PDF資料 |
PDF描述 |
|---|---|
| ADM1026JST-REEL | Complete Thermal and System Management Controller |
| ADM1026JSTZ-REEL | Complete Thermal and System Management Controller |
| ADM1026JST | Circular Connector; No. of Contacts:28; Series:LJT06R; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:19; Circular Contact Gender:Pin; Circular Shell Style:Straight Plug; Insert Arrangement:19-28 |
| ADM1030ARQ | Intelligent Temperature Monitor and PWM Fan Controller |
| ADM1030 | Circular Connector; No. of Contacts:66; Series:LJT06R; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:19; Circular Contact Gender:Socket; Circular Shell Style:Straight Plug; Insert Arrangement:19-35 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADM1026EBZEVB | 功能描述:BOARD EVAL FOR ADM1026 RoHS:否 類別:編程器，開發系統 >> 過時/停產零件編號 系列:- 標準包裝:1 系列:- 傳感器類型:CMOS 成像，彩色（RGB） 傳感范圍:WVGA 接口:I²C 靈敏度:60 fps 電源電壓:5.7 V ~ 6.3 V 嵌入式:否 已供物品:成像器板 已用 IC / 零件:KAC-00401 相關產品:4H2099-ND - SENSOR IMAGE WVGA COLOR 48-PQFP4H2094-ND - SENSOR IMAGE WVGA MONO 48-PQFP |
| ADM1026JST | 功能描述:IC CNTRL SYS REF/EEPROM 48LQFP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓撲:ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6 |
| ADM1026JST-REEL | 功能描述:IC CNTRL SYS REF/EEPROM 48LQFP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓撲:ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6 |
| ADM1026JST-REEL7 | 功能描述:IC CNTRL SYS REF/EEPROM 48LQFP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓撲:ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6 |
| ADM1026JSTZ | 功能描述:PMIC 解決方案 HI INT SYS MONITR IC RoHS:否 制造商:Texas Instruments 安裝風格:SMD/SMT 封裝 / 箱體:QFN-24 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。