- 您現在的位置：買賣IC網 > PDF目錄373996 > ADM1064 (Analog Devices, Inc.) Super Sequencer with Voltage Readback ADC PDF資料下載
參數資料
| 型號： | ADM1064 |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | Super Sequencer with Voltage Readback ADC |
| 中文描述： | 超級序列與ADC的電壓回讀 |
| 文件頁數： | 14/32頁 |
| 文件大小： | 523K |
| 代理商： | ADM1064 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁
ADM1064
INPUT COMPARATOR HYSTERESIS
The UV and OV comparators shown in Figure 19 are always
looking at VPn. To avoid chattering (multiple transitions when
the input is very close to the set threshold level), these compara-
tors have digitally programmable hysteresis. The hysteresis can
be programmed up to the values shown in Table 5.
Rev. 0 | Page 14 of 32
The hysteresis is added after a supply voltage goes out of
tolerance. Therefore, the user can program how much above the
UV threshold the input must rise again before a UV fault is
deasserted. Similarly, the user can program how much below the
OV threshold an input must fall again before an OV fault is
deasserted.
The hysteresis figure is given by
V
HYST
=
V
R
×
N
THRESH
/255
where:
V
HYST
is the desired hysteresis voltage.
N
THRESH
is the decimal value of the 5-bit hysteresis code.
Note that
N
THRESH
has a maximum value of 31. The maximum
hysteresis for the ranges is listed in Table 5.
INPUT GLITCH FILTERING
The final stage of the SFDs is a glitch filter. This block provides
time-domain filtering on the output of the SFD comparators.
This allows the user to remove any spurious transitions such as
supply bounce at turn-on. The glitch filter function is additional
to the digitally programmable hysteresis of the SFD compara-
tors. The glitch filter timeout is programmable up to 100 μs.
For example, when the glitch filter timeout is 100 μs, any pulses
appearing on the input of the glitch filter block that are less than
100 μs in duration are prevented from appearing on the output
of the glitch filter block. Any input pulse that is longer than
100 μs does appear on the output of the glitch filter block. The
output is delayed with respect to the input by 100 μs. The
filtering process is shown in Figure 20.
0
T
0
T
GF
T
0
T
GF
T
0
T
GF
T
0
T
GF
INPUT
INPUT PULSE SHORTER
THAN GLITCH FILTER TIMEOUT
INPUT PULSE LONGER
THAN GLITCH FILTER TIMEOUT
OUTPUT
PROGRAMMED
TIMEOUT
PROGRAMMED
TIMEOUT
INPUT
OUTPUT
Figure 20. Input Glitch Filter Function
SUPPLY SUPERVISION WITH VXn INPUTS
The VXn inputs have two functions. They can be used as either
supply fault detectors or digital logic inputs. When selected as
an analog (SFD) input, the VXn pins have very similar func-
tionality to the VH and VPn pins. The major difference is that
the VXn pins have only one input range: 0.573 V to 1.375 V.
Therefore, these inputs can directly supervise only the very low
supplies. However, the input impedance of the VXn pins is high,
allowing an external resistor divide network to be connected to
the pin. Thus, any supply can be potentially divided down into
the input range of the VXn pin and supervised. This enables the
ADM1064 to monitor other supplies such as +24 V, +48 V, and
5 V.
An additional supply supervision function is available when the
VXn pins are selected as digital inputs. In this case, the analog
function is available as a second detector on each of the dedi-
cated analog inputs, VP1–4 and VH. The analog function of
VX1 is mapped to VP1, VX2 is mapped to VP2, and so on. VX5
is mapped to VH. In this case, these SFDs can be viewed as a
secondary or warning SFD.
The secondary SFDs are fixed to the same input range as the
primary SFD. They are used to indicate warning levels rather
than failure levels. This allows faults and warnings to be gener-
ated on a single supply using only one pin. For example, if VP1
is set to output a fault if a 3.3 V supply droops to 3.0 V, VX1 can
be set to output a warning at 3.1 V. Warning outputs are available
for readback from the status registers. They are also OR’ed
together and fed into the sequencing engine (SE), allowing
warnings to generate interrupts on the PDOs. Therefore, in the
example above, if the supply droops to 3.1 V, a warning is
generated, and remedial action can be taken before the supply
drops out of tolerance.
相關PDF資料 |
PDF描述 |
|---|---|
| ADM1064ACP | Super Sequencer with Voltage Readback ADC |
| ADM1064ACP-REEL | Super Sequencer with Voltage Readback ADC |
| ADM1064ACP-REEL7 | Super Sequencer with Voltage Readback ADC |
| ADM1064ASU | Super Sequencer with Voltage Readback ADC |
| ADM1064ASU-REEL | Super Sequencer with Voltage Readback ADC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADM1064ACP | 制造商:Analog Devices 功能描述:Volt Supervisor Sequencer 2.7V to 5.4V 40-Pin LFCSP EP |
| ADM1064ACP-REEL | 制造商:Analog Devices 功能描述:Volt Supervisor Sequencer 2.7V to 5.4V 40-Pin LFCSP EP T/R |
| ADM1064ACP-REEL7 | 制造商:Analog Devices 功能描述:Volt Supervisor Sequencer 2.7V to 5.4V 40-Pin LFCSP EP T/R |
| ADM1064ACPZ | 功能描述:IC SEQUENCER/SUPERVISOR 40-LFCSP RoHS:是 類別:集成電路 (IC) >> PMIC - 監控器 系列:Super Sequencer® 標準包裝:1 系列:- 類型:簡單復位/加電復位 監視電壓數目:1 輸出:開路漏極或開路集電極 復位:高有效 復位超時:- 電壓 - 閥值:1.8V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:6-TSOP（0.059"，1.50mm 寬）5 引線 供應商設備封裝:5-TSOP 包裝:剪切帶 (CT) 其它名稱:NCP301HSN18T1GOSCT |
| ADM1064ASU | 制造商:Analog Devices 功能描述:Volt Supervisor Sequencer 2.7V to 5.4V 48-Pin TQFP |
發布緊急采購，3分鐘左右您將得到回復。