- 您現在的位置：買賣IC網 > PDF目錄374032 > ADSP-21061LKB-160 (ANALOG DEVICES INC) ADSP-2106x SHARC DSP Microcomputer Family PDF資料下載
參數資料
| 型號： | ADSP-21061LKB-160 |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 數字信號處理 |
| 英文描述： | ADSP-2106x SHARC DSP Microcomputer Family |
| 中文描述： | 48-BIT, 40 MHz, OTHER DSP, PBGA225 |
| 封裝： | PLASTIC, BGA-225 |
| 文件頁數： | 18/47頁 |
| 文件大小： | 367K |
| 代理商： | ADSP-21061LKB-160 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁當前第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁
–18–
ADSP-21061/ADSP-21061L
REV. B
TIMING SPECIFICATIONS
GENERAL NOTES
The following timing specifications are target specifications and
are based on device simulation only.
The timing specifications shown are based on a CLKIN frequency
of 40 MHz (t
CK
= 25 ns). The DT derating allows specifications
at other CLKIN frequencies (within the min–max range of the
t
CK
specification; see Clock Input below). DT is the differ-
ence between the actual CLKIN period and a CLKIN period
of 25 ns:
DT
=
t
CK
– 25
ns
Use the exact timing information given. Do not attempt to
derive parameters from the addition or subtraction of others.
While addition or subtraction would yield meaningful results for
an individual device, the values given in this data sheet reflect
statistical variations and worst cases. Consequently, you cannot
meaningfully add parameters to derive longer times.
See Figure 26 under Test Conditions for voltage reference
levels.
Switching Characteristics
specify how the processor changes its
signals. You have no control over this timing—circuitry external
to the processor must be designed for compatibility with these
signal characteristics. Switching characteristics tell you what the
processor will do in a given circumstance. You can also use switch-
ing characteristics to ensure that any timing requirement of a de-
vice connected to the processor (such as memory) is satisfied.
Timing Requirements
apply to signals that are controlled by
circuitry external to the processor, such as the data input for a
read operation. Timing requirements guarantee that the proces-
sor operates correctly with other devices.
(O/D) = Open Drain
(A/D) = Active Drive
ABSOLUTE MAXIMUM RATINGS (3.3 V DEVICE)*
Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to +4.6 V
Input Voltage . . . . . . . . . . . . . . . . . . . . –0.5 V to V
DD
+ 0.5 V
Output Voltage Swing . . . . . . . . . . . . . –0.5 V to V
DD
+ 0.5 V
Load Capacitance . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200 pF
Junction Temperature Under Bias . . . . . . . . . . . . . . . . 130
°
C
Storage Temperature Range . . . . . . . . . . . . –65
°
C to +150
°
C
Lead Temperature (5 seconds) . . . . . . . . . . . . . . . . . +280
°
C
*Stresses greater than those listed above may cause permanent damage to the
device. These are stress ratings only; functional operation of the device at these or
any other conditions greater than those indicated in the operational sections of this
specification is not implied. Exposure to absolute maximum rating conditions for
extended periods may affect device reliability.
ABSOLUTE MAXIMUM RATINGS (5 V DEVICE)*
Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to +7 V
Input Voltage . . . . . . . . . . . . . . . . . . . . –0.5 V to V
DD
+ 0.5 V
Output Voltage Swing . . . . . . . . . . . . . –0.5 V to V
DD
+ 0.5 V
Load Capacitance . . . . . . . . . . . . . . . . . . . . . . . . . . . . 200 pF
Junction Temperature Under Bias . . . . . . . . . . . . . . . . 130
°
C
Storage Temperature Range . . . . . . . . . . . . –65
°
C to +150
°
C
Lead Temperature (5 seconds) . . . . . . . . . . . . . . . . . +280
°
C
*Stresses greater than those listed above may cause permanent damage to the
device. These are stress ratings only; functional operation of the device at these or
any other conditions greater than those indicated in the operational sections of this
specification is not implied. Exposure to absolute maximum rating conditions for
extended periods may affect device reliability.
ESD SENSITIVITY
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000V readily
accumulate on the human body and test equipment and can discharge without detection. Although
the ADSP-2106x features proprietary ESD protection circuitry, permanent damage may occur on
devices subjected to high-energy electrostatic discharges. Therefore, proper ESD precautions are
recommended to avoid performance degradation or loss of functionality.
WARNING!
ESD SENSITIVE DEVICE
相關PDF資料 |
PDF描述 |
|---|---|
| ADSP-21061LKB-176 | ADSP-2106x SHARC DSP Microcomputer Family |
| ADSP-21061LKS-160 | ADSP-2106x SHARC DSP Microcomputer Family |
| ADSP-21061LKS-176 | ADSP-2106x SHARC DSP Microcomputer Family |
| ADSP-21062CS-160 | ADSP-2106x SHARC DSP Microcomputer Family |
| ADSP-21062KS-133 | ADSP-2106x SHARC DSP Microcomputer Family |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADSP-21061LKB-176 | 制造商:AD 制造商全稱:Analog Devices 功能描述:DSP Microcomputer Family |
| ADSP-21061LKBZ-160 | 功能描述:IC DSP CONTROLLER 32BIT 225-BGA RoHS:是 類別:集成電路 (IC) >> 嵌入式 - DSP（數字式信號處理器） 系列:SHARC® 標準包裝:2 系列:StarCore 類型:SC140 內核 接口:DSI，以太網，RS-232 時鐘速率:400MHz 非易失內存:外部 芯片上RAM:1.436MB 電壓 - 輸入/輸出:3.30V 電壓 - 核心:1.20V 工作溫度:-40°C ~ 105°C 安裝類型:表面貼裝 封裝/外殼:431-BFBGA，FCBGA 供應商設備封裝:431-FCPBGA（20x20） 包裝:托盤 |
| ADSP21061LKS160 | 制造商:Analog Devices 功能描述:DSP Floating-Point 32-Bit 40MHz 40MIPS 240-Pin MQFP Tray |
| ADSP-21061LKS-160 | 制造商:Rochester Electronics LLC 功能描述:ADSP-21061 1MBIT,40MHZ, 3V SHARC - Bulk 制造商:Analog Devices 功能描述:IC SHARC DSP 40MHZ 21061 MQFP240 |
| ADSP-21061LKS-176 | 制造商:Analog Devices 功能描述:DSP Floating-Point 32-Bit 44MHz 44MIPS 240-Pin MQFP Tray 制造商:Rochester Electronics LLC 功能描述:ADSP-21061L 44HZ, 3V SHARC - Bulk |
發布緊急采購，3分鐘左右您將得到回復。