- 您現在的位置：買賣IC網 > Datasheet目錄39 > ADT7463ARQZ-REEL (ON Semiconductor)IC REMOTE THERMAL CTRLR 24-QSOP Datasheet資料下載
參數資料
| 型號： | ADT7463ARQZ-REEL |
| 廠商： | ON Semiconductor |
| 文件頁數： | 44/50頁 |
| 文件大小： | 726K |
| 描述： | IC REMOTE THERMAL CTRLR 24-QSOP |
| 產品變化通告： | MFG CHG Notification ADI to ON Semi QSOP 24ld Pkg (MSL) Change 17/Jun/2010 |
| 標準包裝： | 2,500 |
| 系列： | dBCool® |
| 功能： | 風扇控制，溫度監控器 |
| 傳感器類型： | 內部和外部 |
| 感應溫度： | -40°C ~ 120°C，外部傳感器 |
| 精確度： | ±1.5°C（最小值） |
| 拓撲： | ADC，比較器，風扇速度計數器，多路復用器，寄存器庫 |
| 輸出類型： | SMBus? |
| 輸出警報： | 無 |
| 輸出風扇： | 是 |
| 電源電壓： | 3 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 120°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 24-SSOP（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 24-QSOP |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁當前第44頁第45頁第46頁第47頁第48頁第49頁第50頁
ADT7463
http://onsemi.com
44
Table 66. PWM MIN DUTY CYCLE REGISTERS (Note 1)
Register Address
R/W
Description
PowerOn Default
0x64
R/W
PWM1 Min Duty Cycle
0x80 (50% Duty Cycle)
0x65
R/W
PWM2 Min Duty Cycle
0x80 (50% Duty Cycle)
0x66
R/W
PWM3 Min Duty Cycle
0x80 (50% Duty Cycle)
1. These registers become readonly when the ADT7463 is in automatic fan control mode.
Table 67. PWM MIN DUTY CYCLE REGISTER BITS
Bit
Name
R/W
Description
<7:0>
PWM Duty Cycle
R/W
These bits define the PWM
MIN
duty cycle for PWMx.
0x00 = 0% Duty Cycle (Fan Off)
0x40 = 25% Duty Cycle
0x80 = 50% Duty Cycle
0xFF = 100% Duty Cycle (Fan Full Speed)
Table 68. T
MIN
REGISTERS (Note 1)
Register Address
R/W
Description (Note 2)
PowerOn Default
0x67
R/W
Remote 1 Temperature T
MIN
0x5A (90癈)
0x68
R/W
Local Temperature T
MIN
0x5A (90癈)
0x69
R/W
Remote 2 Temperature T
MIN
0x5A (90癈)
1. These registers become readonly when the Configuration Register 1 Lock bit is set. Further attempts to write to these registers have no
effect.
2. These are the T
MIN
registers for each temperature channel. When the temperature measured exceeds T
MIN
, the appropriate fan runs at
minimum speed and increase with temperature according to T
RANGE
.
Table 69. THERM
LIMIT REGISTERS (Note 1)
Register Address
R/W
Description (Note 2)
PowerOn Default
0x6A
R/W
Remote 1 THERM
Limit
0x64 (100癈)
0x6B
R/W
Local THERM
Limit
0x64 (100癈)
0x6C
R/W
Remote 2 THERM
Limit
0x64 (100癈)
1. This register becomes readonly when the Configuration Register 1 Lock bit is set to 1. Further attempts to write to this register have no effect.
2. If any temperature measured exceeds its THERM
limit, all PWM outputs drive their fans at 100% duty cycle. This is a failsafe mechanism
incorporated to cool the system in the event of a critical overtemperature. It also ensures some level of cooling in the event that software
or hardware locks up. If set to 0x80, this feature is disabled. The PWM output remains at 100% until the temperature drops below THERM
Limit Hysteresis. If the THERM
pin is programmed as an output, exceeding these limits by 0.25癈 can cause the THERM
pin to assert low
as an output.
Table 70. TEMPERATURE HYSTERESIS REGISTERS (Note 1)
Register Address
R/W
Description (Note 2)
PowerOn Default
0x6D
R/W
Remote 1 Local Temperature Hysteresis
0x44
0x6E
R/W
Remote 2 Temperature Hysteresis
0x40
1. This register becomes readonly when the Configuration Register 1 Lock bit is set to 1. Further attempts to write to this register have no effect.
2. Each 4bit value controls the amount of temperature hysteresis applied to a particular temperature channel. Once the temperature for that
channel falls below its T
MIN
value, the fan remains running at PWM
MIN
duty cycle until the temperature = T
MIN
Hysteresis. Up to 15癈 of
hysteresis may be assigned to any temperature channel. The hysteresis value chosen also applies to that temperature channel if its THERM
limit is exceeded. The PWM output being controlled goes to 100% if the THERM
limit is exceeded and remains at 100% until the temperature
drops below THERM
Hysteresis. For acoustic reasons, it is recommended that the hysteresis value not be programmed less than 4癈.
Setting the hysteresis value lower than 4癈 causes the fan to switch on and off regularly when the temperature is close to T
MIN.
相關PDF資料 |
PDF描述 |
|---|---|
| ADT7476AARQZ-R | IC REMOTE THERMAL CTLR 24QSOP |
| ADT7481ARMZ-1RL | IC SENSOR TEMP 2CH ALARM 10MSOP |
| ADT7482ARMZ-REEL | IC SENSOR TEMP 2CH ALARM 10MSOP |
| ADT7485AARMZ-R | IC TEMP/VOLT DGL SENS SST 10MSOP |
| ADT7486AARMZ-RL | IC TEMP SENS DGTL 2CH SST 10MSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADT7463ARQZ-REEL7 | 功能描述:IC REMOTE THERMAL CTRLR 24-QSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱管理 系列:dBCool® 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓撲:ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6 |
| ADT7466 | 制造商:AD 制造商全稱:Analog Devices 功能描述:dBCool Remote Thermal Controller and Voltage Monitor |
| ADT7466ARQZ | 功能描述:板上安裝溫度傳感器 RMT THRM CTR VLT MON RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| ADT7466ARQZ-REEL | 功能描述:板上安裝溫度傳感器 RMT THRM CTR VLT MON RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| ADT7466ARQZ-REEL7 | 功能描述:IC REMOTE THERMAL CTRLR 16QSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱管理 系列:dBCool® 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓撲:ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6 |
發布緊急采購，3分鐘左右您將得到回復。