- 您現在的位置：買賣IC網 > Datasheet目錄39 > ADT7482ARMZ-REEL (ON Semiconductor)IC SENSOR TEMP 2CH ALARM 10MSOP Datasheet資料下載
參數資料
| 型號： | ADT7482ARMZ-REEL |
| 廠商： | ON Semiconductor |
| 文件頁數： | 10/20頁 |
| 文件大小： | 282K |
| 描述： | IC SENSOR TEMP 2CH ALARM 10MSOP |
| 產品變化通告： | MFG CHG Notification ADI to ON Semi |
| 標準包裝： | 3,000 |
| 功能： | 溫度監控系統（傳感器） |
| 傳感器類型： | 內部和外部 |
| 感應溫度： | -40°C ~ 125°C，外部傳感器 |
| 精確度： | ±2.5°C（最小值） |
| 拓撲： | ADC，比較器，多路復用器，寄存器庫 |
| 輸出類型： | SMBus? |
| 輸出警報： | 是 |
| 輸出風扇： | 是 |
| 電源電壓： | 3 V ~ 3.6 V |
| 工作溫度： | -40°C ~ 125°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 10-TFSOP，10-MSOP（0.118"，3.00mm 寬） |
| 供應商設備封裝： | 10-MSOP |
| 包裝： | 帶卷 (TR) |
ADT7482
http://onsemi.com
10
Table 10. CONFIGURATION 2 REGISTER (ADDRESS 0x24)
Bit
Mnemonic
Function
7
Lock Bit
Setting this bit to 1 locks all lockable registers to their current values. This prevents tampering with settings
until the device is powered down. Default = 0.
<6:0>
Res
Reserved for future use.
Conversion Rate Register
The conversion rate register is at Address 0x04 for reads
and Address 0x0A for writes. The four LSBs of this register
are used to program the conversion times from 15.5 ms
(Code 0x0A) to 16 seconds (Code 0x00). To program the
ADT7482 to perform continuous measurements, set the
conversion rate register to 0x0B. For example, a conversion
rate of 8 conversions/second means that, beginning at
125 ms intervals, the device performs a conversion on the
local and the remote temperature channels. The four MSBs
of this register are reserved and should not be written to.
This register can be written to and read back over the
SMBus. The default value of this register is 0x07, giving a
rate of 8 conversions per second. Use of slower conversion
times greatly reduces the device power consumption.
Limit Registers
The ADT7482 has three limits for each temperature
channel: high, low, and THERM
temperature limits for
local, Remote 1, and Remote 2 temperature measurements.
The remote temperature high and low limits span two
registers each, to contain an upper and lower byte for each
limit. There is also a THERM
hysteresis register. All limit
registers can be written to and read back over the SMBus.
See Table 16 for limit register addresses and power-on
default values.
When Pin 8 is configured as an ALERT
output, the high
limit registers perform a > comparison while the low limit
registers perform a ?comparison. For example, if the high
limit register is programmed with 80癈, then measuring
81癈 results in an out-of-limit condition, setting a flag in the
status register. If the low limit register is programmed with
0癈, measuring 0癈 or lower results in an out-of-limit
condition.
Exceeding either the local or remote THERM
limit asserts
THERM
low. When Pin 8 is configured as THERM2
,
exceeding either the local or remote high limit asserts
THERM2
low. A default hysteresis value of 10癈 is
provided that applies to both THERM
channels. This
hysteresis value can be reprogrammed.
It is important to remember that the temperature limits
data format is the same as the temperature measurement data
format. If the temperature measurement uses the default
binary scale, then the temperature limits also use the binary
scale. If the temperature measurement scale is switched,
however, the temperature limits do not switch automatically.
The limit registers must be reprogrammed to the desired
value in the correct data format. For example, if the remote
low limit is set at 10癈 and the default binary scale is used,
the limit register value should be 0000 1010b. If the scale is
switched to offset binary, the value in the low temperature
limit register should be reprogrammed to be 0100 1010b.
Table 11. CONVERSION RATE/CHANNEL SELECTOR REGISTER (READ ADDRESS 0x04, WRITE ADDRESS 0x0A)
Bit
Mnemonic
Function
7
Reserved
Reserved for Future Use. Do Not Write to this Bit.
6
Reserved
Reserved for Future Use. Do Not Write to this Bit.
5
Reserved
Reserved for Future Use. Do Not Write to this Bit.
4
Reserved
Reserved for Future Use. Do Not Write to this Bit.
<3:0>
Conversion Rates
These Bits Set how often the ADT7482 Measures each Temperature Channel.
Conversions/sec
Time (seconds)
0000 = 0.0625
16
0001 = 0.125
8
0010 = 0.25
4
0011 = 0.5
2
0100 = 1
1
0101 = 2
500 m
0110 = 4
250 m
0111 = 8 = Default
125 m
1000 = 16
62.5 m
1001 = 32
31.25 m
1010 = 64
15.5 m
相關PDF資料 |
PDF描述 |
|---|---|
| ADT7485AARMZ-R | IC TEMP/VOLT DGL SENS SST 10MSOP |
| ADT7486AARMZ-RL | IC TEMP SENS DGTL 2CH SST 10MSOP |
| ADT7488AARMZ-RL | IC TEMP/VOLT DGTL W/SST 10MSOP |
| ADT7518ARQZ | IC SENSOR TEMP QD ADC/DAC 16QSOP |
| AT30TS00-MAH-T | SENSOR DGTL TEMP I2C/SMBUS 8WDFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADT7482ARMZ-REEL7 | 功能描述:IC SENSOR TEMP 2CH ALARM 10MSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱管理 系列:- 標準包裝:1 系列:- 功能:溫度監控系統（傳感器） 傳感器類型:內部和外部 感應溫度:-40°C ~ 125°C，外部傳感器 精確度:±2.5°C 本地（最大值），±5°C 遠程（最大值） 拓撲:ADC，比較器，寄存器庫 輸出類型:2 線 SMBus? 輸出警報:無 輸出風扇:無 電源電壓:2.7 V ~ 5.5 V 工作溫度:-40°C ~ 125°C 安裝類型:表面貼裝 封裝/外殼:SOT-23-8 供應商設備封裝:SOT-23-8 包裝:Digi-Reel® 其它名稱:296-22675-6 |
| ADT7482ARMZ-RL7 | 功能描述:板上安裝溫度傳感器 2 CH TEMP SNSR/ALARM 2 WIRE SMBUS INTRFCE RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| ADT7483A | 制造商:AD 制造商全稱:Analog Devices 功能描述:Dual Channel Temperature Sensor and Over Temperature Alarm |
| ADT7483AARQZ | 功能描述:板上安裝溫度傳感器 2 TEMP DIODE MONITOR 2 WIRE SMBUS INTRFCE RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| ADT7483AARQZ-R7 | 功能描述:板上安裝溫度傳感器 2 TEMP DIODE MONITOR 2 WIRE SMBUS INTRFCE RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
發布緊急采購，3分鐘左右您將得到回復。