- 您現在的位置：買賣IC網 > Datasheet目錄39 > ADT7518ARQZ (Analog Devices Inc)IC SENSOR TEMP QD ADC/DAC 16QSOP Datasheet資料下載
參數資料
| 型號： | ADT7518ARQZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 22/40頁 |
| 文件大小： | 891K |
| 描述： | IC SENSOR TEMP QD ADC/DAC 16QSOP |
| 標準包裝： | 98 |
| 功能： | 溫度監控系統（傳感器） |
| 傳感器類型： | 內部和外部 |
| 感應溫度： | -40°C ~ 120°C，外部傳感器 |
| 精確度： | ±3°C（最小值） |
| 拓?fù)洌?/td> | ADC，比較器，多路復用器，寄存器庫 |
| 輸出類型： | I²C?，MICROWIRE?，QSPI?，SPI? |
| 輸出警報： | 無 |
| 輸出風扇： | 無 |
| 電源電壓： | 2.7 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 120°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 16-SSOP（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 16-QSOP |
| 包裝： | 托盤 |
| 產品目錄頁面： | 798 (CN2011-ZH PDF) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁當前第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁
ADT7518
Rev. A | Page 22 of 40
WATCHDOG
LIMIT
COMPARISONS
INTERRUPT
MASK
REGISTERS
CONTROL
CONFIGURATION
REGISTER 1
INTERRUPT
STATUS
REGISTER
(TEMP AND
AIN1 TO AIN4)
INTERRUPT
STATUS
REGISTER 2
(V
DD
)
READ RESET
S/W RESET
INTERNAL
TEMP
INT/INT
(LATCHED OUTPUT)
INT/INT
ENABLE BIT
EXTERNAL
TEMP
V
DD
DIODE
FAULT
AIN1AIN4
Figure 49. Interrupt Structure
AIN Interrupts
The measured results from the AIN inputs are compared with
the AIN VHIGH (greater than comparison) and VLOW (less than or
equal to comparison) limits. An interrupt occurs if the AIN
inputs exceed or equal the limit registers. These voltage limits
are stored in on-chip registers. Note that the limit registers are
8 bits long while the AIN conversion result is 10 bits long. If the
voltage limits are not masked out, then any out-of-limit com-
parisons generate flags that are stored in the Interrupt Status 1
register (Address = 00h) and one or more out-of-limit results
will cause the INT/INT
output to pull either high or low
depending on the output polarity setting. It is good design
practice to mask out interrupts for channels that are of no
concern to the application. Figure 49 shows the interrupt
structure for the ADT7518. It gives a block diagram
representation of how the various measurement channels affect
the INT/INT
pin.
FUNCTIONAL DESCRIPTIONMEASUREMENT
Temperature Sensor
The ADT7518 contains an ADC with special input signal
conditioning to enable operation with external and on-chip
diode temperature sensors. When the ADT7518 is operating in
single-channel mode, the ADC continually processes the
measurement taken on one channel only. This channel is
preselected by Bits C0:C2 in the Control Configuration 2
register (Address 19h). When in round robin mode, the analog
input multiplexer sequentially selects the VDD input channel, the
on-chip temperature sensor to measure its internal temperature,
either the external temperature sensor or AIN1 and AIN2,
AIN3, and then AIN4. These signals are digitized by the ADC
and the results are stored in the various value registers.
The measured results from the temperature sensors are com-
pared with the internal and external T
HIGH
, T
LOW
limits. These
temperature limits are stored in on-chip registers. If the temp-
erature limits are not masked, any out-of-limit comparisons
generate flags that are stored in the Interrupt Status 1 register.
One or more out-of-limit results will cause the INT/INT
output
to pull either high or low depending on the output polarity
setting.
Theoretically, the temperature measuring circuit can measure
temperatures from 128癈 to +127癈 with a resolution of
0.25癈. However, temperatures outside TA are outside the
guaranteed operating temperature range of the device. Temp-
erature measurement from 128癈 to +127癈 is possible using
an external sensor.
Temperature measurement is initiated by three methods. The
first method is applicable when the part is in single-channel
measurement mode. The temperature is measured 16 times and
internally averaged to reduce noise. In single-channel mode, the
part is continuously monitoring the selected channel, i.e., as
soon as one measurement is taken another one is started on the
same channel. The total time to measure a temperature channel
with the ADC operating at slow speed is typically 11.4 ms
(712 祍 ?16) for the internal temperature sensor and 24.22 ms
(1.51 ms ?16) for the external temperature sensor. The new
temperature value is stored in two 8-bit registers and is ready
for reading by the I
2
C or SPI interface. The user has the option
of disabling the averaging by setting Bit 5 in the Control
Configuration 2 register (Address 19h). The ADT7518 defaults
on power-up with averaging enabled.
相關PDF資料 |
PDF描述 |
|---|---|
| AT30TS00-MAH-T | SENSOR DGTL TEMP I2C/SMBUS 8WDFN |
| AT30TSE002B-MAH-T | SENSOR DGTL TEMP I2C/SMBUS 8WDFN |
| BD3504FVM-TR | IC REG CTRLR SGL POS ADJ 8MSOP |
| BD3521FVM-TR | IC REG CTRLR SGL 1.5V MSOP8 |
| BD9153MUV-E2 | IC REG TRPL BCK/LINEAR 24VQFN |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADT7518ARQZ-REEL | 制造商:Analog Devices 功能描述:Temp Sensor Analog Serial (4-Wire, SPI, I2C) 16-Pin QSOP T/R |
| ADT7518ARQZ-REEL7 | 制造商:Analog Devices 功能描述:Temp Sensor Analog Serial (4-Wire, SPI, I2C) 16-Pin QSOP T/R |
| ADT7519 | 制造商:AD 制造商全稱:Analog Devices 功能描述:SPI-/I2C-Compatible, Temperature Sensor,4-Channel ADC and Quad Voltage Output |
| ADT7519ARQ | 制造商:Analog Devices 功能描述:Temp Sensor Digital Serial (4-Wire, SPI, I2C) 16-Pin QSOP |
| ADT7519ARQ-REEL | 制造商:Analog Devices 功能描述:Temp Sensor Digital Serial (4-Wire, SPI, I2C) 16-Pin QSOP T/R |
發布緊急采購，3分鐘左右您將得到回復。