欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: ADUC842BCP32-5
廠商: ANALOG DEVICES INC
元件分類: 微控制器/微處理器
英文描述: MicroConverter 12-Bit ADCs and DACs with Embedded High Speed 62-kB Flash MCU
中文描述: 8-BIT, FLASH, 16.78 MHz, MICROCONTROLLER, QCC56
封裝: 8 X 8 MM, LEAD FRAME, MO-220VLLD2, CSP-56
文件頁數: 65/88頁
文件大?。?/td> 903K
代理商: ADUC842BCP32-5
ADuC841/ADuC842/ADuC843
UART SERIAL INTERFACE
The serial port is full-duplex, meaning it can transmit and
receive simultaneously. It is also receive-buffered, meaning it
can begin receiving a second byte before a previously received
byte has been read from the receive register. However, if the first
byte still has not been read by the time reception of the second
byte is complete, the first byte is lost. The physical interface to
the serial data network is via Pins RxD(P3.0) and TxD(P3.1),
while the SFR interface to the UART is comprised of SBUF and
SCON, as described below.
Rev. 0 | Page 65 of 88
Table 32. SCON SFR Bit Designations
Bit No.
Name
7
SM0
6
SM1
SBUF
Both the serial port receive and transmit registers are accessed
through the SBUF SFR (SFR address = 99H). Writing to SBUF
loads the transmit register, and reading SBUF accesses a
physically separate receive register.
SCON UART
SFR Address
Power-On Default
Bit Addressable
Serial Port Control Register
98H
00H
Yes
Description
UART Serial Mode Select Bits.
These bits select the serial port operating mode as follows:
SM0
SM1
Selected Operating Mode.
0
0
Mode 0: Shift Register, fixed baud rate (Core_Clk/2).
0
1
Mode 1: 8-bit UART, variable baud rate.
1
0
Mode 2: 9-bit UART, fixed baud rate (Core_Clk/32) or (Core_Clk/16).
1
1
Mode 3: 9-bit UART, variable baud rate.
Multiprocessor Communication Enable Bit.
Enables multiprocessor communication in Modes 2 and 3.
In Mode 0, SM2 must be cleared.
In Mode 1, if SM2 is set, RI is not activated if a valid stop bit was not received. If SM2 is cleared, RI is set as soon as the
byte of data has been received.
In Modes 2 or 3, if SM2 is set, RI is not activated if the received 9th data bit in RB8 is 0.
If SM2 is cleared, RI is set as soon as the byte of data has been received.
Serial Port Receive Enable Bit.
Set by user software to enable serial port reception.
Cleared by user software to disable serial port reception.
Serial Port Transmit (Bit 9).
The data loaded into TB8 is the 9th data bit transmitted in Modes 2 and 3.
Serial Port Receiver Bit 9.
The 9th data bit received in Modes 2 and 3 is latched into RB8. For Mode 1, the stop bit is latched into RB8.
Serial Port Transmit Interrupt Flag.
Set by hardware at the end of the 8th bit in Mode 0, or at the beginning of the stop bit in Modes 1, 2, and 3.
TI must be cleared by user software.
Serial Port Receive Interrupt Flag.
Set by hardware at the end of the 8th bit in Mode 0, or halfway through the stop bit in Modes 1, 2, and 3.
RI must be cleared by software.
5
SM2
4
REN
3
TB8
2
RB8
1
TI
0
RI
相關PDF資料
PDF描述
ADUC843BCP32-5 MicroConverter 12-Bit ADCs and DACs with Embedded High Speed 62-kB Flash MCU
ADUC842BCP8-3 MicroConverter 12-Bit ADCs and DACs with Embedded High Speed 62-kB Flash MCU
ADUC843BCP8-3 MicroConverter 12-Bit ADCs and DACs with Embedded High Speed 62-kB Flash MCU
ADUC842BCP8-5 MicroConverter 12-Bit ADCs and DACs with Embedded High Speed 62-kB Flash MCU
ADUC843BCP8-5 MicroConverter 12-Bit ADCs and DACs with Embedded High Speed 62-kB Flash MCU
相關代理商/技術參數
參數描述
ADUC842BCP62-3 制造商:Analog Devices 功能描述:MCU 8-bit ADuC8xx 8052 CISC 62KB Flash 3V 56-Pin LFCSP EP
ADUC842BCP62-3U 制造商:Analog Devices 功能描述:MICROCONVERTER 1-CYCLE VERSION ADUC833 - Trays
ADUC842BCP62-3-U2 制造商:Analog Devices 功能描述:MICROCONVERTER 1-CYCLE VERSION ADUC834 - Trays
ADUC842BCP62-5 制造商:Rochester Electronics LLC 功能描述: 制造商:Analog Devices 功能描述:
ADUC842BCP8-3 制造商:Analog Devices 功能描述: 制造商:Rochester Electronics LLC 功能描述:
主站蜘蛛池模板: 平顺县| 从化市| 化德县| 洱源县| 冀州市| 平阳县| 华安县| 神池县| 孟津县| 花垣县| 万年县| 东山县| 墨脱县| 万宁市| 图们市| 葵青区| 万年县| 丹棱县| 临安市| 黔江区| 永定县| 小金县| 日喀则市| 泽州县| 枣庄市| 雷州市| 定襄县| 乳山市| 田东县| 彭州市| 潞西市| 保康县| 年辖:市辖区| 郑州市| 松阳县| 葫芦岛市| 新营市| 开阳县| 莱州市| 东城区| 日喀则市|