- 您現在的位置：買賣IC網 > PDF目錄374040 > ADUC848BS32-3 (ANALOG DEVICES INC) MicroConverter Multichannel 24-/16-Bit ADCs with Embedded 62 kB Flash and Single-Cycle MCU PDF資料下載
參數資料
| 型號： | ADUC848BS32-3 |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | MicroConverter Multichannel 24-/16-Bit ADCs with Embedded 62 kB Flash and Single-Cycle MCU |
| 中文描述： | 8-BIT, FLASH, 12.58 MHz, MICROCONTROLLER, PQFP52 |
| 封裝： | 14 X 14 MM, PLASTIC, MO-112-AC-1, MQFP-52 |
| 文件頁數： | 41/108頁 |
| 文件大?。?/td> | 1109K |
| 代理商： | ADUC848BS32-3 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁當前第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁
ADuC845/ADuC847/ADuC848
ADCMODE (ADC MODE REGISTER)
Used to control the operational mode of both ADCs.
Rev. A | Page 41 of 108
SFR Address:
Power-On Default:
Bit Addressable:
D1H
08H
No
Table 24. ADCMODE SFR Bit Designations
Bit No.
Name
7
–––
6
REJ60
Description
Not Implemented. Write Don’t Care.
Automatic 60 Hz Notch Select Bit.
Setting this bit places a notch in the frequency response at 60 Hz, allowing simultaneous 50 Hz and 60 Hz
rejection at an SF word of 82 decimal. This 60 Hz notch can be set only if SF ≥ 68 decimal, that is, the regular
filter notch must be ≤
60 Hz. This second notch is placed at 60 Hz only if the device clock is at 32.768 kHz.
Primary ADC Enable.
Set by the user to enable the primary ADC and place it in the mode selected in MD2–MD0 below.
Cleared by the user to place the primary ADC into power-down mode.
Auxiliary (ADuC845 only) ADC Enable.
Set by the user to enable the auxiliary (ADuC845 only) ADC and place it in the mode selected in MD2–MD0
below.
Cleared by the user to place the auxiliary (ADuC845 only) ADC in power-down mode.
Chop Mode Disable.
Set by the user to disable chop mode on both the primary and auxiliary (ADuC845 only) ADC allowing a
three times higher ADC data throughput. SF values as low as 3 are allowed with this bit set, giving up to
1.3 kHz ADC update rates.
Cleared by the user to enable chop mode on both the primary and auxiliary (ADuC845 only) ADC.
Primary and Auxiliary (ADuC845 only) ADC Mode Bits.
These bits select the operational mode of the enabled ADC as follows:
MD2
MD1
MD0
0
0
0
ADC Power-Down Mode (Power-On Default).
0
0
1
Idle Mode. In idle mode, the ADC filter and modulator are held in a reset state
although the modulator clocks are still provided.
0
1
0
Single Conversion Mode. In single conversion mode, a single conversion is performed
on the enabled ADC. Upon completion of a conversion, the ADC data registers
(ADC0H/M/L and/or ADC1H/M/L (ADuC845 only)) are updated. The relevant flags in
the ADCSTAT SFR are written, and power-down is re-entered with the MD2MD0
accordingly being written to 000.
Note that ADC0L is not available on the ADuC848.
0
1
1
Continuous Conversion. In continuous conversion mode, the ADC data registers are
regularly updated at the selected update rate (see the Sinc Filter SFR Bit Designations
in Table 28).
1
0
0
Internal Zero-Scale Calibration. Internal short automatically connected to the
enabled ADC input(s).
1
0
1
Internal Full-Scale Calibration. Internal or external REFIN± or REFIN2± V
REF
(as
determined by XREF bits in ADC0CON2 and/or AXREF (ADuC845 only) in ADC1CON
(ADuC845 only) is automatically connected to the enabled ADC input(s) for this
calibration.
1
1
0
System Zero-Scale Calibration. User should connect system zero-scale input to the
enabled ADC input(s) as selected by CH3–CH0 and ACH3–ACH0 bits in the
ADC0CON2 and ADC1CON (ADuC845 only) registers.
1
1
1
System Full-Scale Calibration. User should connect system full-scale input to the
enabled ADC input(s) as selected by CH3–CH0 and ACH3–ACH0 bits in the
ADC0CON2 and ADC1CON (ADuC845 only) registers.
5
ADC0EN
4
ADC1EN
(ADuC845 only)
3
CHOP
2, 1, 0
MD2, MD1, MD0
相關PDF資料 |
PDF描述 |
|---|---|
| ADUC848BS32-5 | MicroConverter Multichannel 24-/16-Bit ADCs with Embedded 62 kB Flash and Single-Cycle MCU |
| ADUC848BS62-3 | 10-825944-010 |
| ADUC848BS62-5 | MicroConverter Multichannel 24-/16-Bit ADCs with Embedded 62 kB Flash and Single-Cycle MCU |
| ADUC848BS8-3 | MicroConverter Multichannel 24-/16-Bit ADCs with Embedded 62 kB Flash and Single-Cycle MCU |
| ADUC848BS8-5 | MicroConverter Multichannel 24-/16-Bit ADCs with Embedded 62 kB Flash and Single-Cycle MCU |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADUC848BS32-5 | 制造商:Analog Devices 功能描述:IC MICROCONTROLLER |
| ADUC848BS62-3 | 制造商:Rochester Electronics LLC 功能描述:8BIT CISC 62KB FLASH 12.85MHZ 3.3V 52MQFP - Bulk 制造商:Analog Devices 功能描述: |
| ADUC848BS62-5 | 制造商:Rochester Electronics LLC 功能描述:8BIT CISC 62KB FLASH 12.85MHZ 5V 52MQFP - Bulk 制造商:Analog Devices 功能描述:IC MICROCONTROLLER |
| ADUC848BS8-3 | 制造商:Analog Devices 功能描述: |
| ADUC848BS8-5 | 制造商:Analog Devices 功能描述:MCU 8-bit ADuC8xx 8052 CISC 62KB Flash 3.3V/5V 52-Pin MQFP 制造商:Analog Devices 功能描述:IC MICROCONTROLLER |
發布緊急采購，3分鐘左右您將得到回復。