- 您現在的位置：買賣IC網 > PDF目錄374046 > ADV7180BCPZ (ANALOG DEVICES INC) 10-Bit, 4 x Oversampling SDTV Video Decoder PDF資料下載
參數資料
| 型號： | ADV7180BCPZ |
| 廠商： | ANALOG DEVICES INC |
| 元件分類： | 顏色信號轉換 |
| 英文描述： | 10-Bit, 4 x Oversampling SDTV Video Decoder |
| 中文描述： | COLOR SIGNAL DECODER, QCC40 |
| 封裝： | 6 X 6 MM, ROHS COMPLIANT, MO-220VJJD-2, LFCSP-40 |
| 文件頁數： | 108/112頁 |
| 文件大小： | 1320K |
| 代理商： | ADV7180BCPZ |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁當前第108頁第109頁第110頁第111頁第112頁
ADV7180
PCB LAYOUT RECOMMENDATIONS
The ADV7180 is a high precision, high speed, mixed-signal
device. To achieve the maximum performance from the part, it
is important to have a well laid out PCB. The following is a
guide for designing a board using the ADV7180.
ANALOG INTERFACE INPUTS
Care should be taken when routing the inputs on the PCB.
Track lengths should be kept to a minimum, and 75 Ω trace
impedances should be used when possible. In addition, trace
impedances other than 75 Ω increase the chance of reflections.
POWER SUPPLY DECOUPLING
It is recommended to decouple each power supply pin with
0.1 μF and 10 nF capacitors. The fundamental idea is to have a
decoupling capacitor within about 0.5 cm of each power pin.
Also avoid placing the capacitor on the opposite side of the PCB
from the ADV7180, because doing so interposes resistive vias in
the path. The decoupling capacitors should be located between
the power plane and the power pin. Current should flow from
the power plane to the capacitor and then to the power pin. Do
not make the power connection between the capacitor and the
power pin. Placing a via underneath the 100 nF capacitor pads,
down to the power plane, is generally
the best approach (see
Figure 51).
Rev. A | Page 108 of 112
Experience has repeatedly shown that the noise performance is
the same or better with a single ground plane. Using multiple
ground planes can be detrimental because each separate ground
plane is smaller, and long ground loops can result.
When using separate ground planes is unavoidable, placing a single
ground plane under the ADV7180 is recommended. The location
of the split should be under the ADV7180. In this case, it is even
more important to place components wisely because the current
loops are much longer, and current takes the path of least
resistance. An example of a current loop is a power plane to the
ADV7180 to the digital output trace to the digital data receiver to
the digital ground plane to the analog ground plane.
PLL
Place the PLL loop filter components as close as possible to the
ELPF pin. It should also be placed on the same side of the PCB
as the ADV7180. Do not place any digital or other high
frequency traces near these components. Use the values
suggested in the data sheet with tolerances of 10% or less.
VREFN AND VREFP
The circuit associated with these pins should be placed as close
as possible and on the same side of the PCB as the ADV7180.
DIGITAL OUTPUTS (BOTH DATA AND CLOCKS)
Try to minimize the trace length that the digital outputs have to
drive. Longer traces have higher capacitance, requiring more
current and in turn causing more internal digital noise. Shorter
traces reduce the possibility of reflections.
Adding a 30 Ω to 50 Ω series resistor can suppress reflections,
reduce EMI, and reduce the current spikes inside the ADV7180.
If series resistors are used, place them as close as possible to the
ADV7180 pins. However, try not to add vias or extra length to
the output trace to make the resistors closer.
If possible, limit the capacitance that each of the digital outputs
drives to less than 15 pF. This can easily be accomplished by
keeping traces short and by connecting the outputs to only one
device. Loading the outputs with excessive capacitance increases
the current transients inside the ADV7180, creating more
digital noise on its power supplies.
The ADV7180 LFCSP-40 has an exposed metal paddle on the
bottom of the LFCSP package. This paddle must be soldered to
PCB ground for proper heat dissipation and also for noise and
mechanical strength benefits.
DIGITAL INPUTS
The digital inputs on the ADV7180 are designed to work with
3.3 V signals and are not tolerant of 5 V signals. Extra
components are needed if 5 V logic signals are required to be
applied to the decoder.
VDD
GND
10nF
100nF
VIA TO SUPPLY
VIA TO GND
0
Figure 51. Recommended Power Supply Decoupling
It is particularly important to maintain low noise and good
stability of P
VDD
. Careful attention must be paid to regulation,
filtering, and decoupling. It is highly desirable to provide
separate regulated supplies for each of the analog circuitry
groups (A
Some graphic controllers use substantially different levels of
power when active (during active picture time) and when idle
(during horizontal and vertical sync periods). This can result in
a measurable change in the voltage supplied to the analog
supply regulator, which can in turn produce changes in the
regulated analog supply voltage. This can be mitigated by
regulating the analog supply, or at least P
cleaner power source, for example, from a 12 V supply.
Using a single ground plane for the entire board is also
recommended. This ground plane should have a space between
the analog and digital sections of the PCB (see Figure 52).
VDD
, D
VDD
, D
VDDIO
, and P
VDD
).
VDD
, from a different,
ANALOG
SECTION
DIGITAL
SECTION
ADV7180
0
Figure 52. PCB Ground Layout
相關PDF資料 |
PDF描述 |
|---|---|
| ADV7180BSTZ | 10-Bit, 4 x Oversampling SDTV Video Decoder |
| ADV7181 | Multiformat SDTV Video Decoder |
| ADV7181B | Multiformat SDTV Video Decoder |
| ADV7181BBCPZ | Multiformat SDTV Video Decoder |
| ADV7181BBSTZ | Multiformat SDTV Video Decoder |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ADV7180BCPZ | 制造商:Analog Devices 功能描述:IC VIDEO DECODER 10BIT 57.27MSPS LFCSP40 |
| ADV7180BCPZ-REEL | 功能描述:IC VIDEO DECODER SDTV 40-LFCSP RoHS:是 類別:集成電路 (IC) >> 線性 - 視頻處理 系列:- 產品變化通告:Product Discontinuation 07/Mar/2011 標準包裝:3,000 系列:OMNITUNE™ 類型:調諧器 應用:移動電話，手機，視頻顯示器 安裝類型:表面貼裝 封裝/外殼:65-WFBGA 供應商設備封裝:PG-WFSGA-65 包裝:帶卷 (TR) 其它名稱:SP000365064 |
| ADV7180BST48Z | 功能描述:IC VID DECOD SDTV 10BIT 48LQFP RoHS:是 類別:集成電路 (IC) >> 線性 - 視頻處理 系列:- 標準包裝:250 系列:- 類型:電平移位器 應用:LCD 電視機/監控器 安裝類型:表面貼裝 封裝/外殼:28-WFQFN 裸露焊盤 供應商設備封裝:28-WQFN（4x4）裸露焊盤 包裝:帶卷 (TR) 其它名稱:296-32523-2TPS65198RUYT-ND |
| ADV7180BST48Z-RL | 功能描述:視頻 IC 48-Lead Low Profile Quad Flat Package RoHS:否 制造商:Fairchild Semiconductor 工作電源電壓:5 V 電源電流:80 mA 最大工作溫度:+ 85 C 封裝 / 箱體:TSSOP-28 封裝:Reel |
| ADV7180BSTZ | 功能描述:IC VIDEO DECODER SDTV 64-LQFP RoHS:是 類別:集成電路 (IC) >> 線性 - 視頻處理 系列:- 標準包裝:250 系列:- 類型:電平移位器 應用:LCD 電視機/監控器 安裝類型:表面貼裝 封裝/外殼:28-WFQFN 裸露焊盤 供應商設備封裝:28-WQFN（4x4）裸露焊盤 包裝:帶卷 (TR) 其它名稱:296-32523-2TPS65198RUYT-ND |
發布緊急采購，3分鐘左右您將得到回復。