- 您現在的位置：買賣IC網 > PDF目錄379665 > AMBE2000 (Electronic Theatre Controls, Inc.) VOCODER CHIP PDF資料下載
參數資料
| 型號： | AMBE2000 |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | VOCODER CHIP |
| 中文描述： | 聲碼器芯片 |
| 文件頁數： | 42/47頁 |
| 文件大小： | 324K |
| 代理商： | AMBE2000 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁當前第42頁第43頁第44頁第45頁第46頁第47頁
AMBE-2000 Vocoder Chip
User’s Manual Version 3.0
page 42
Visit us at
www.dvsinc.com
Confidential Proprietary, Subject to Change
7.7
Slip Enable
In any real time communication system, clock skew issues must be anticipated to keep the flow of data smooth from one end of
the system to the other. The SLIP_EN (pin 82) signal allows the encoder of the AMBE-2000 to react to small slips in the
encoder channel signals. When the AMBE-2000 is in active (parallel or serial) mode, the chip produces the signals
internally for the transfer of data. Because the transmission channel will then likely be driven by this timing, the necessity of
controlling slip becomes a moot point.
Any time the AMBE-2000 encoder channel is in one of the passive modes and the channel timing is asynchronous to the
A/D-D/A clock (very rarely are these two interfaces coupled) then the SLIP_EN pin should be set active high.
The AMBE-2000 Vocoder chip processes speech in voice frames that are approximately 20 ms in duration. When
configured appropriately the chip provides a slip control feature that automatically adjusts the frame size to either 160 or 161
speech samples per frame. This slip control feature allows the vocoder chip to compensate for drift between the frame and
sample rate clocks on the order of approximately 0.6% (6,000 ppm.) The vocoder chip also accepts Slip Control Packets that
extend the range of allowable frame sizes to be between 159 and 161 samples per voice frame. When properly used these Slip
Control Packets provide the designer with additional flexibility in dealing with clock drift.
There are three recommended methods for using slip control on the AMBE-2000 Vocoder Chips which are described below.
The system designer should select the method that best meets the needs of their system configuration. Also included is some
background information on the operation of the AMBE-2000 in passive mode
In order to help understand Slip control feature here is a brief description on reading encoder packets from the AMBE-2000 in
passive formatted mode.
When transmitting a packet, the AMBE-2000 writes a Header = 0x13ec followed by 23 words of data, followed by 0xfffe into
the transmit (i.e. output) buffer. The terminating word 0xfffe is written into the transmit buffer by the AMBE-2000 at the end
of each encoder packet. Normally in passive mode this terminating word is in the transmit buffer at the beginning of each
transmission cycle (from the previous frame) and so it is the first word output whenever a packet is transmitted. If the encoder
packet is ready, then the second output word will be the packet Header=0x13ec followed by 23 words of data. However if the
packet is not ready then the AMBE-2000 will continue to output the terminating word (0xfffe) until the packet is ready and
placed in the transmit buffer. At this point the full 24 word packet beginning with the Header will be output on subsequent
transmissions. This process continues for each packet transmission which occurs nominally every 20 ms, provided that each 24
word packet (Header + 23 data words) is read in full. If the full 24 words of the packet are not read from the AMBE-2000, then
the chip’s transmit buffer will contain some words left over from a previous packet. Generally these words would be 0x0000
for lower data rates which don't use the last words of the packet. This case should be avoided:
It is recommended that in passive formatted mode the system always read packets by requesting
words from the AMBE-2000 until a packet Header is received and then continuing to request 23
additional output words from the AMBE-2000 until a total of 24 words beginning with the Header
word = 0x13ec are received. Any words output by the AMBE-2000 prior to the Header should be
ignored by the system (except for monitoring as discussed in Method 3 below).
相關PDF資料 |
PDF描述 |
|---|---|
| AMC0802A | CONTOUR DRAWING & BLOCK DIAGRAM |
| AMC317 | 1.5A / 3- TERMINAL ADJUSTABLE REGULATOR |
| AMC317T | 1.5A / 3- TERMINAL ADJUSTABLE REGULATOR |
| AMC317ST | 1.5A / 3- TERMINAL ADJUSTABLE REGULATOR |
| AMC5902 | 6CH Motor Driver for CD-ROM, DVD-ROM |
相關代理商/技術參數 |
參數描述 |
|---|---|
| AMB-EHS160 | 制造商:Schroff/Pentair Electronic Packaging 功能描述: |
| AMBF22 | 制造商:ABRACON 制造商全稱:Abracon Corporation 功能描述:MULTILAYER CHIP BALANCE-EMI FILTER |
| AMBI LIGHT SENSOR | 制造商:LIQUIDWARE 功能描述:Ambient Light Sensor |
| AMB-KIT1 | 功能描述:TEST LEAD SET FOR INSUL RESIST 制造商:amprobe 系列:AMB 包裝:袋 零件狀態:有效 套件類型:測試引線 內容:短頭鱷魚夾，測試引線，測試探針 標準包裝:1 |
| AMB-KIT2 | 制造商:Amprobe Test Tools 功能描述:10 KV SHIELDED LEAD WITH TIP FOR AMB-110 AMB-110 |
發布緊急采購，3分鐘左右您將得到回復。