- 您現在的位置：買賣IC網 > PDF目錄385414 > HY29F040A (Hynix Semiconductor Inc.) 512K x 8-bit CMOS 5.0 volt-only, Sector Erase Flash Memory PDF資料下載
參數資料
| 型號： | HY29F040A |
| 廠商： | Hynix Semiconductor Inc. |
| 英文描述： | 512K x 8-bit CMOS 5.0 volt-only, Sector Erase Flash Memory |
| 中文描述： | 為512k × 8位CMOS 5.0伏只，扇區擦除閃存 |
| 文件頁數： | 10/40頁 |
| 文件大小： | 282K |
| 代理商： | HY29F040A |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁當前第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁
10
HY29F040A
During Sector Erase operation, data bit DQ7 shows
a logical “0”. This operation is known as
/Data Polling. Sector Erase operation is complete
when data on DQ7 is a logical “1” (see Write Opera-
tion Status section) at which time the
device returns to read mode. At this time, the
address pins are no longer latched. Note that
/Data Polling must be performed at a sector
address within any of the sectors being erased and
not a protected sector to ensure that DQ7 returns
a logical “1” upon completion of the Sector Erase
operation.
Figure 2 illustrates the Sector Erase Algorithm us-
ing typical command strings and bus operations.
During execution of the Sector Erase command, only
the Erase Suspend and Erase Resume com-
mands are allowed. All other commands will reset
the device to read mode. Note: Do not attempt to
write an invalid command sequence during the
sector erase operation. Doing so will terminate the
sector erase operation and the device will reset to
the read mode.
Erase Suspend/Erase Resume
Commands
The Erase Suspend command allows the user to
interrupt a Sector Erase operation and read data
from or program to a sector that is not being erased.
The Erase Suspend command onthe HY29F040 also
allows for Byte Programming during the suspended
erase from a sector not being erased. The Erase
Suspend command is applicable only during Sector
Erase operation and will be ignored if written during
the Chip Erase operation or Byte Programming op-
eration. The Erase Suspend command (B0H) will
be allowed only during the Sector Erase opera-
tion, including, but not limited to, the sector erase
time-out period after any Sector Erase commands
(30H) have been initiated.
Writing the Erase Suspend command during the
time-out will result in immediate termination of the
time-out period. Any subsequent writes of the Sec-
tor Erase command will be taken as the Erase
Resume command (30H). Note that any other com-
mands during the time-out will reset the
device to the read mode. The address pins are
don’t-cares when writing the Erase Suspend or
Erase Resume commands.
When the Erase Suspend command is written dur-
ing a Sector Erase operation, the chip will take a
maximum of 15
m
s to suspend the erase opera-
tion and go into erase suspended-read mode.
During this time, the system can monitor the /Data
Polling or Toggle Bit write operation status flags to
determine when the device has entered erase sus-
pend-read mode (see Write Operation Status sec-
tion). The system must use an address of an eras-
ing sector to monitor /Data Polling or Toggle Bit to
determine if the Sector Erase operation has been
suspended.
In the erase suspend-read mode, the system can
read data from any sector that is not being erased.
A read from a sector being erased may result in
invalid data.
After the system writes the Erase Suspend com-
mand and waits until the Toggle Bit stops toggling,
data reads from the device may then be performed.
Any further writes of the Erase Suspend command
at this time will be ignored.
To resume operation of Sector Erase, the Erase
Resume command (30H) should be written. Any
further writes of the Erase Resume command at
this point will be ignored. Another Erase Suspend
command can be written after the chip has re-
sumed the Sector Erase operation.
相關PDF資料 |
PDF描述 |
|---|---|
| HY29F080T70 | 8 Megabit (1M x 8), 5 Volt-only, Flash Memory |
| HY29F080 | 8 Megabit (1M x 8), 5 Volt-only, Flash Memory |
| HY29F080G12 | 8 Megabit (1M x 8), 5 Volt-only, Flash Memory |
| HY29F080G70 | 8 Megabit (1M x 8), 5 Volt-only, Flash Memory |
| HY29F080G90 | 8 Megabit (1M x 8), 5 Volt-only, Flash Memory |
相關代理商/技術參數 |
參數描述 |
|---|---|
| HY29F040AC-12 | 制造商:HYNIX 制造商全稱:Hynix Semiconductor 功能描述:512K x 8-bit CMOS 5.0 volt-only, Sector Erase Flash Memory |
| HY29F040AC-12E | 制造商:HYNIX 制造商全稱:Hynix Semiconductor 功能描述:512K x 8-bit CMOS 5.0 volt-only, Sector Erase Flash Memory |
| HY29F040AC-12I | 制造商:HYNIX 制造商全稱:Hynix Semiconductor 功能描述:512K x 8-bit CMOS 5.0 volt-only, Sector Erase Flash Memory |
| HY29F040AC-15 | 制造商:HYNIX 制造商全稱:Hynix Semiconductor 功能描述:512K x 8-bit CMOS 5.0 volt-only, Sector Erase Flash Memory |
| HY29F040AC-15E | 制造商:HYNIX 制造商全稱:Hynix Semiconductor 功能描述:512K x 8-bit CMOS 5.0 volt-only, Sector Erase Flash Memory |
發布緊急采購，3分鐘左右您將得到回復。