- 您現在的位置：買賣IC網 > PDF目錄360998 > ISP1130N (NXP SEMICONDUCTORS) Universal Serial Bus compound hub with integrated keyboard controller PDF資料下載
參數資料
| 型號： | ISP1130N |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 微控制器/微處理器 |
| 英文描述： | Universal Serial Bus compound hub with integrated keyboard controller |
| 中文描述： | SPECIALTY MICROPROCESSOR CIRCUIT, PDIP56 |
| 封裝： | PLASTIC, SDIP-56 |
| 文件頁數： | 25/68頁 |
| 文件大小： | 1786K |
| 代理商： | ISP1130N |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁當前第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁
Philips Semiconductors
ISP1130
USB compound hub with keyboard controller
Objective specification
Rev. 01 — 23 March 2000
25 of 68
9397 750 06895
Philips Electronics N.V. 2000. All rights reserved.
9.1.3
Set Mode command
Selects the operating mode and (de)activates features. The command is followed by
one data write, containing the Configuration byte.
Code (Hex) —
F3
Transaction —
write 1 byte (Configuration).
9.2 Data flow commands
Data flow commands are used to manage the data transmission between the USB
endpoints and the embedded microcontroller. Much of the data flow is initiated via an
interrupt to the microcontroller. The data flow commands are used to access the
endpoints and determine whether the endpoint FIFOs contain valid data.
Remark:
The IN buffer of an endpoint contains input data
for
the host, the OUT buffer
receives output data
from
the host.
9.2.1
Read Interrupt Register command
Shows the source(s) of an interrupt to the microcontroller. After writing the command,
two bytes are read which hold the interrupt register contents. Byte 1 contains the
least significant bits (7 to 0), byte 2 the most significant bits (15 to 8).
Code (Hex) —
F4
Transaction —
read 2 bytes.
Table 25: Set Mode command, Configuration byte: bit allocation
Bit
7
6
5
4
3
2
1
0
Symbol
-
Clock
Restart
String
Descriptor
Enable
0
W
Remote
WakeUp
Enable
0
W
Always
PLL
Clock
0
W
Use
IntDn
Resistor
0
W
-
Interrupt
OnNAK
Reset
Access
X
W
0
W
0
W
1
W
Table 26: Set Mode command, Configuration byte: bit description
Bit
Symbol
7
-
6
ClockRestart
Description
reserved
A logic 1 will cause a clock restart for 2 ms upon a bus transition, when the device
is in ‘suspend’ mode. This allows the device to wake up without resume signaling.
A logic 1 enables the string descriptor. The default string will be sent to the host
upon request.
A logic 1 enables remote wake-up by key press (embedded function 1).
A logic 1 indicates that the internal clocks and PLL are always running, even in
‘suspend’ mode. A logic 0 stops the internal clock, crystal oscillator and PLL.
A logic 1 causes the downstream pull-down resistors to be connected.
reserved; must always be logic 0
A logic 1 will generate an interrupt upon sending a NAK. A logic 0 will only report
successful transactions.
5
StringDescriptorEnable
4
3
RemoteWakeUpEnable
AlwaysPLLClock
2
1
0
UseIntDnResistor
-
InterruptOnNAK
相關PDF資料 |
PDF描述 |
|---|---|
| ISP1160 | Embedded Universal Serial Bus Host Controller |
| ISP1160BD | Embedded Universal Serial Bus Host Controller |
| ISP1160BM | Embedded Universal Serial Bus Host Controller |
| ISP1161A | Full-speed Universal Serial Bus single-chip host and device controller |
| ISP1161ABD | Full-speed Universal Serial Bus single-chip host and device controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISP1160 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Embedded Universal Serial Bus Host Controller |
| ISP1160BD | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Embedded Universal Serial Bus Host Controller |
| ISP1160BD,157 | 功能描述:USB 接口集成電路 USB 1.1 HOST CONTROLLER RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| ISP1160BD/01 | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Embedded Universal Serial Bus Host Controller |
| ISP1160BD/01,118 | 功能描述:USB 接口集成電路 USB HOST CTRL RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
發布緊急采購，3分鐘左右您將得到回復。