- 您現在的位置：買賣IC網 > PDF目錄360999 > ISP1562 (NXP Semiconductors N.V.) Hi-Speed Universal Serial Bus PCI Host Controller PDF資料下載
參數資料
| 型號： | ISP1562 |
| 廠商： | NXP Semiconductors N.V. |
| 英文描述： | Hi-Speed Universal Serial Bus PCI Host Controller |
| 中文描述： | 高速通用串行總線PCI主機控制器 |
| 文件頁數： | 61/98頁 |
| 文件大小： | 442K |
| 代理商： | ISP1562 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁當前第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁
9397 750 14223
Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet
Rev. 01 — 14 July 2005
61 of 98
Philips Semiconductors
ISP1562
USB PCI Host Controller
11.2 EHCI controller capability registers
Other than the OHCI Host Controller, there are some registers in EHCI that define the
capability of EHCI. The address range of these registers is located before the operational
registers.
11.2.1
CAPLENGTH/HCIVERSION register
The bit allocation of this 4 B register is given in
Table 86
.
2
PSS
On read—
PortSuspendStatus
: This bit indicates whether the port is
suspended or is in the resume sequence. It is set by a SetSuspendState
write and cleared when PSSC (PortSuspendStatusChange) is set at the
end of the resume interval. This bit is not set if CCS
(CurrentConnectStatus) is cleared. This bit is also cleared when PRSC is
set at the end of the port reset or when the Host Controller is placed in the
USBRESUME state. If an upstream resume is in progress, it will propagate
to the Host Controller.
0 —
Port is not suspended
1 —
Port is suspended.
On write—
SetPortSuspend
: The HCD can set the PSS
(PortSuspendStatus) bit by writing logic 1 to this bit. Writing logic 0 has no
effect. If CCS is cleared, this write does not set PSS; instead it sets CSS.
This informs the driver that it attempted to suspend a disconnected port.
On read—
PortEnableStatus
: This bit indicates whether the port is enabled
or disabled. The Root Hub may clear this bit when an overcurrent condition,
disconnect event, switched-off power or operational bus error is detected.
This change also causes PortEnabledStatusChange to be set. The HCD
can set this bit by writing SetPortEnable and clear it by writing
ClearPortEnable. This bit cannot be set when CCS (CurrentConnectStatus)
is cleared. This bit is also set on completing a port reset when
ResetStatusChange is set or on completing a port suspend when
SuspendStatusChange is set.
0 —
Port is disabled
1 —
Port is enabled.
On write—
SetPortEnable
: The HCD can set PES (PortEnableStatus) by
writing logic 1. Writing logic 0 has no effect. If CCS is cleared, this write
does not set PES, but instead sets CSC (ConnectStatusChange). This
informs the driver that it attempted to enable a disconnected port.
On read—
CurrentConnectStatus
: This bit reflects the current state of the
downstream port.
0 —
No device connected
1 —
Device connected.
On write—
ClearPortEnable
: The HCD can write logic 1 to this bit to clear
the PES (PortEnableStatus) bit. Writing logic 0 has no effect. The CCS bit is
not affected by any write.
Remark:
This bit always reads logic 1 when the attached device is
nonremovable (DeviceRemovable[NDP]).
1
PES
0
CCS
Table 85:
HcRhPortStatus[4:1] - Host Controller Root Hub Port Status[4:1] register bit
description
…continued
Address: Value read from func0 or func1 of address 10h + 54h
Bit
Symbol
Description
相關PDF資料 |
PDF描述 |
|---|---|
| ISP1562BE | Hi-Speed Universal Serial Bus PCI Host Controller |
| ISP1581 | Universal Serial Bus 2.0 high-speed interface device |
| ISP1581BD | Universal Serial Bus 2.0 high-speed interface device |
| ISP1582 | Hi-Speed Universal Serial Bus peripheral controller |
| ISP1582BS | Hi-Speed Universal Serial Bus peripheral controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISP1562BE | 制造商:PHILIPS 制造商全稱:NXP Semiconductors 功能描述:Hi-Speed USB PCI host controller |
| ISP1562BE,518 | 功能描述:USB 接口集成電路 USB 2.0 PCI HOST RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| ISP1562BE,551 | 功能描述:USB 接口集成電路 USB 2.0 PCI HOST RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| ISP1562BE,557 | 功能描述:USB 接口集成電路 DO NOT USE ORDER -S OR -T PART RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| ISP1562BEGA | 功能描述:IC USB HOST CTRL HI-SPD 100LQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 專用 系列:- 標準包裝:3,000 系列:- 應用:PDA，便攜式音頻/視頻，智能電話 接口:I²C，2 線串口 電源電壓:1.65 V ~ 3.6 V 封裝/外殼:24-WQFN 裸露焊盤 供應商設備封裝:24-QFN 裸露焊盤（4x4） 包裝:帶卷 (TR) 安裝類型:表面貼裝 產品目錄頁面:1015 (CN2011-ZH PDF) 其它名稱:296-25223-2 |
發布緊急采購，3分鐘左右您將得到回復。