- 您現在的位置：買賣IC網 > PDF目錄360999 > ISP1582BS (NXP SEMICONDUCTORS) Hi-Speed Universal Serial Bus peripheral controller PDF資料下載
參數資料
| 型號： | ISP1582BS |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 總線控制器 |
| 英文描述： | Hi-Speed Universal Serial Bus peripheral controller |
| 中文描述： | UNIVERSAL SERIAL BUS CONTROLLER, PQCC56 |
| 封裝： | 8 X 8 MM, 0.85 MM PITCH, PLASTIC, MO-220, SOT-684-1, HVQFN-56 |
| 文件頁數： | 12/66頁 |
| 文件大小： | 325K |
| 代理商： | ISP1582BS |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁當前第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁
Philips Semiconductors
ISP1582
Hi-Speed USB peripheral controller
Preliminary data
Rev. 03 — 25 August 2004
12 of 66
9397 750 13699
Koninklijke Philips Electronics N.V. 2004. All rights reserved.
8.6.3
HS detection
The ISP1582 handles more than one electrical state—full-speed (FS) or high-speed
(HS)—under the USB specification. When the USB cable is connected from the
peripheral to the host controller, the ISP1582 defaults to the FS state until it sees a
bus reset from the host controller.
During the bus reset, the peripheral initiates an HS chirp to detect whether the host
controller supports Hi-Speed USB or Original USB. Chirping must be done with the
pull-up resistor connected and the internal termination resistors disabled. If the HS
handshake shows that there is an HS host connected, then the ISP1582 switches to
the HS state.
In the HS state, the ISP1582 should observe the bus for periodic activity. If the bus
remains inactive for 3 ms, the peripheral switches to the FS state to check for a
Single-Ended Zero (SE0) condition on the USB bus. If an SE0 condition is detected
for the designated time (100
μ
s to 875
μ
s; refer to section 7.1.7.6 of the USB
specification Rev. 2.0), the ISP1582 switches to the HS chirp state to perform an HS
detection handshake. Otherwise, the ISP1582 remains in the FS state adhering to the
bus-suspend specification.
8.7 Philips Serial Interface Engine (SIE)
The Philips SIE implements the full USB protocol layer. It is completely hardwired for
speed and needs no firmware intervention. The functions of this block include:
synchronization pattern recognition, parallel or serial conversion, bit (de)stuffing,
CRC checking or generation, Packet IDentifier (PID) verification or generation,
address recognition, handshake evaluation or generation.
8.8 SoftConnect
The connection to the USB is established by pulling pin DP (for full-speed devices)
HIGH through a 1.5 k
pull-up resistor. In the ISP1582, an external 1.5 k
pull-up
resistor must be connected between pin RPU and 3.3 V. Pin RPU connects the
pull-up resistor to pin DP, when bit SOFTCT in the Mode register is set (see
Table 20
and
Table 21
). After a hardware reset, the pull-up resistor is disconnected by default
(bit SOFTCT = 0). The USB bus reset does not change the value of bit SOFTCT.
When the V
BUS
is not present, the SOFTCT bit must be set to logic 0 to comply with
the back-drive voltage.
8.9 System controller
The system controller implements the USB power-down capabilities of the ISP1582.
Registers are protected against data corruption during wake-up following a resume
(from the suspend state) by locking the write access until an unlock code has been
written in the Unlock Device register (see
Table 73
and
Table 74
).
8.10 Output pins status
Table 3
illustrates the behavior of output pins when V
CC(I/O)
is supplied with V
CC
in
various operating conditions.
相關PDF資料 |
PDF描述 |
|---|---|
| ISP1583 | Hi-Speed Universal Serial Bus peripheral controller |
| ISP1583BS | Hi-Speed Universal Serial Bus peripheral controller |
| ISP1760BE | Hi-Speed Universal Serial Bus host controller for embedded applications |
| ISP1760 | Hi-Speed Universal Serial Bus host controller for embedded applications |
| ISP1761 | Hi-Speed Universal Serial Bus On-The-Go controller |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISP1582BS,518 | 功能描述:USB 接口集成電路 USB PERIPH CNTRLR RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| ISP1582BS,551 | 功能描述:USB 接口集成電路 HI-SPEED USB2 DEVICE RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| ISP1582BS,557 | 功能描述:USB 接口集成電路 HI-SPEED USB2 DEVICE RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| ISP1582BSGA | 功能描述:IC UBS CTRL HI-SPEED 56HVQFN RoHS:是 類別:集成電路 (IC) >> 接口 - 專用 系列:- 標準包裝:3,000 系列:- 應用:PDA，便攜式音頻/視頻，智能電話 接口:I²C，2 線串口 電源電壓:1.65 V ~ 3.6 V 封裝/外殼:24-WQFN 裸露焊盤 供應商設備封裝:24-QFN 裸露焊盤（4x4） 包裝:帶卷 (TR) 安裝類型:表面貼裝 產品目錄頁面:1015 (CN2011-ZH PDF) 其它名稱:296-25223-2 |
| ISP1582BS-S | 功能描述:USB 接口集成電路 HI-SPEED USB2 DEVICE RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
發布緊急采購，3分鐘左右您將得到回復。