- 您現在的位置：買賣IC網 > PDF目錄360999 > ISP1761BE (NXP SEMICONDUCTORS) Hi-Speed Universal Serial Bus On-The-Go controller PDF資料下載
參數資料
| 型號： | ISP1761BE |
| 廠商： | NXP SEMICONDUCTORS |
| 元件分類： | 總線控制器 |
| 英文描述： | Hi-Speed Universal Serial Bus On-The-Go controller |
| 中文描述： | UNIVERSAL SERIAL BUS CONTROLLER, PQFP128 |
| 封裝： | 14 X 20 MM, 1.40 MM HEIGHT, PLASTIC, MS-026, SOT425-1, LQFP-128 |
| 文件頁數： | 99/158頁 |
| 文件大?。?/td> | 724K |
| 代理商： | ISP1761BE |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁當前第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁第154頁第155頁第156頁第157頁第158頁
9397 750 13258
Koninklijke Philips Electronics N.V. 2005. All rights reserved.
Product data sheet
Rev. 01 — 12 January 2005
99 of 158
Philips Semiconductors
ISP1761
Hi-Speed USB OTG controller
initialization of the Peripheral Controller. If DMA is not required by the application,
DMACLKON can be permanently disabled to save current. The burst counter, DMA bus
width, and the polarity of DC_DREQ and DC_DACK must be accordingly set.
The ISP1761 supports only the counter mode DMA transfer. To enable the counter mode,
ensure that DIS_XFER_CNT in the DcDMAConfiguration register (address: 0238h) is set
to zero. Set bit EOT_POL in the DMA Hardware register (address: 023Ch) to logic 1, to
make the EOT function invalid because the ISP1761 does not support the external EOT
mode.
Before starting the DMA transfer, preset the interrupt enable bit IEDMA in the Interrupt
Enable register (address: 0214h) and the DMA Interrupt Enable register (address: 0254h).
The ISP1761 supports two interrupt trigger modes: level and edge. The pulse width, which
in an edge mode, is determined by setting the Interrupt Pulse Width register (address:
0280h). The default value is 1Eh, which indicates that the interrupt pulse width is 1
μ
s.
The minimum interrupt pulse width is approximately 30 ns when set to logic 1. Do not
write a zero to this register.
The interrupt polarity also must be correctly set.
Remark:
DMA can apply to all endpoints on the chip. It, however, can only take place for
one endpoint at a time. The selected endpoint is assigned by setting the endpoint number
in the DMA Endpoint register (address: 0258h). It will also internally redirect the endpoint
buffer of the selected endpoint to the DMA controller bus. In addition, it requires a
preceding process to program the endpoint type, the endpoint maximum packet size, and
the direction of the endpoint.
When setting the Endpoint Index register (address: 022Ch), the endpoint buffer of the
selected endpoint is directed to the internal CPU bus for the PIO access. Therefore, it is
required to reconfigure the Endpoint Index register with endpoint number, which is not an
endpoint number in use for the DMA transfer to avoid any confusion.
10.1.1.4
Starting DMA
Dynamically assign the DMA Transfer Counter register (address: 0234h) for each DMA
transfer.
The transfer will end once transfer counter reaches zero. Bit DMA_XFER_OK in the DMA
Interrupt Reason register (address: 0250h) will be asserted to indicate that the DMA
transfer has successfully stopped. If the transfer counter is larger than the burst counter,
the DC_DREQ signal will drop at the end of each burst transfer. DC_DREQ will reassert at
the beginning of each burst. For a 32-bit DMA transfer, the minimum burst length is 4 B.
This means that the burst length is only one DMA cycle. Therefore, DC_DREQ and
DC_DACK will toggle by each DMA cycle. For a 16-bit DMA transfer, the minimum burst
length is 2 B.
Setting bit GDMA read or GDMA write in the DMA Command register (address: 0230h)
will start the DMA transfer.
10.1.1.5
DMA stop and interrupt handling
The DMA transfer will either successfully complete or terminate, which can be identified
by reading the status in the DcInterrupt register (address: 0218h) and DMA Interrupt
Reason register (address: 0250h) while in the Interrupt Service Routine.
相關PDF資料 |
PDF描述 |
|---|---|
| ISP1761ET | Hi-Speed Universal Serial Bus On-The-Go controller |
| ISP2100A | Telecommunication IC |
| ISP2100BN4 | Microprocessor |
| ISP2300 | Controller Miscellaneous - Datasheet Reference |
| ISP2310 | Controller Miscellaneous - Datasheet Reference |
相關代理商/技術參數 |
參數描述 |
|---|---|
| ISP1761BE,518 | 功能描述:USB 接口集成電路 USB HS OTG CONTROLLER RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| ISP1761BE,551 | 功能描述:USB 接口集成電路 DO NOT USE ORDER -T OR NO "-" RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| ISP1761BE,557 | 功能描述:USB 接口集成電路 USB HS OTG CTRLR RoHS:否 制造商:Cypress Semiconductor 產品:USB 2.0 數據速率: 接口類型:SPI 工作電源電壓:3.15 V to 3.45 V 工作電源電流: 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:WLCSP-20 |
| ISP1761BE518 | 制造商:ST-Ericsson 功能描述:IC CONTROLLER USB OTG 128LQFP |
| ISP1761BEGE | 功能描述:IC USB CTRL HI-SPEED 128LQFP RoHS:是 類別:集成電路 (IC) >> 接口 - 控制器 系列:- 標準包裝:4,900 系列:- 控制器類型:USB 2.0 控制器 接口:串行 電源電壓:3 V ~ 3.6 V 電流 - 電源:135mA 工作溫度:0°C ~ 70°C 安裝類型:表面貼裝 封裝/外殼:36-VFQFN 裸露焊盤 供應商設備封裝:36-QFN（6x6） 包裝:* 其它名稱:Q6396337A |
發布緊急采購，3分鐘左右您將得到回復。