- 您現在的位置：買賣IC網 > Datasheet目錄42 > LTC4260IUH#PBF (Linear Technology)IC HOT SWAP CNTRL I2C 32-QFN Datasheet資料下載
參數資料
| 型號： | LTC4260IUH#PBF |
| 廠商： | Linear Technology |
| 文件頁數： | 14/30頁 |
| 文件大小： | 295K |
| 描述： | IC HOT SWAP CNTRL I2C 32-QFN |
| 標準包裝： | 73 |
| 類型： | 熱交換控制器 |
| 應用： | 通用 |
| 內部開關： | 無 |
| 電源電壓： | 8.5 V ~ 80 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 32-WFQFN 裸露焊盤 |
| 供應商設備封裝： | 32-QFN 裸露焊盤（5x5） |
| 包裝： | 管件 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁
LTC4260
14
4260fc
For more information www.linear.com/LTC4260
During a short circuit, if the current limit sense voltage
exceeds 150mV, the active current limit enters a high cur-
rent protection mode that immediately turns off the output
transistor by pulling the GATE-to-SOURCE voltage to zero.
Current in the output transistor drops from tens of amps
to zero in a few hundred nanoseconds. The input voltage
will drop during the high current and then spike upwards
due to parasitic inductances when the FET shuts off (see
Supply Transients). Following this event, the part may turn
on again after a delay (typically the 100ms normal turn-on
delay if the input voltage drops below the UVLO threshold)
and enters active current limit before shutting off.
Overvoltage Fault
An overvoltage fault occurs when the OV pin rises above
its 3.5V threshold. This shuts off the switch immediately
(with a 1mA current from GATE to ground) and sets the
overvoltage present bit, C0, and the overvoltage fault
bit D0. If the OV pin subsequently falls back below the
threshold for 100ms, the switch will be allowed to turn on
again unless the overvoltage autoretry has been disabled
by clearing bit A0.
Undervoltage Fault
An undervoltage fault occurs when the UV pin falls below
its 3.12V threshold. This turns off the switch immediately
(with a 1mA current from GATE to ground) and sets the
undervoltage present bit, C1, and the undervoltage fault
bit D1. If the UV pin subsequently rises above the thresh-
old for 100ms, the switch will turn on again unless the
applicaTions inForMaTion
V
OUT
50V/DIV
I
OUT
5A/DIV
V
GATE
10V/DIV
TIMER
2V/DIV
100祍/DIV
4260 F03
Figure 3. Short-Circuit Waveforms
undervoltage autoretry has been disabled by clearing bit
A1. When power is applied to the device, if UV is below its
3.12V threshold after INTV
CC
crosses its 4.5V undervoltage
lockout threshold, an undervoltage fault will be logged in
the fault register.
Board Present Change of State
Whenever the BD錚RST pin toggles, bit D4 is set to
indicate a change of state. When the BD錚RST pin goes
high, indicating board removal, the switch turns off im-
mediately (with a 1mA current from GATE to ground) and
clears the board present bit, C4. If the BD錚RST pin is
pulled low, indicating a board insertion, all fault bits except
D4 will be cleared and the board present bit, C4, is set. If
the BD錚RST pin remains low for 100ms the state of the
ON pin will be captured in the FET On Control bit A3. This
turns the switch on if the ON pin is tied high. There is an
internal 10礎 pull-up current source on the BD錚RST pin.
If the system shuts down due to a fault, it may be desirable
to restart the system simply by removing and reinserting
a load card. In cases where the LTC4260 and the switch
reside on a backplane or midplane and the load resides
on a plug-in card, the BD錚RST pin can be used to detect
when the plug-in card is removed (see Figure 4). Once
the plug-in card is reinserted the fault register is cleared
(except for D4). After 100ms the state of the ON pin is
latched into bit A3 of the control register. At this point the
system will start up again.
If a connection sense on the plug-in card is driving the
BD錚RST pin, the insertion or removal of the card may
cause the pin voltage to bounce. This will result in clear-
ing the fault register when the card is removed. The pin
can be debounced using a filter capacitor, C
BD錚RST
, on
the BD錚RST pin as shown in Figure 4. The filter time
is given by:
t
FILTER
= C
BD錚RST
" 123 [ms/礔]
FET Short Fault
A FET short fault will be reported if the data converter
measures a current sense voltage greater than or equal
to 2mV while the FET is turned off. This condition sets the
FET short present bit, C5, and the FET short fault bit D5.
相關PDF資料 |
PDF描述 |
|---|---|
| LTC4261IGN-2#PBF | IC CTRLR HOTSWAP W/ADC 28-SSOP |
| LTC4263IS#TRPBF | IC IEEE 803.2AF CNTRLR 14-SOIC |
| LTC4268IDKD-1#PBF | IC PD HIGH POWER W/CNTRL 32-DFN |
| LTC4274CUHF#PBF | IC CONTROLLER POE 38-QFN |
| LTC4280CUFD#PBF | IC CONTROLLER HOT SWAP QFN-24 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| LTC4261 | 制造商:LINER 制造商全稱:Linear Technology 功能描述:Negative Voltage Hot Swap Controllers with ADC and I2C Monitoring |
| LTC4261CGN | 功能描述:IC CTRLR HOTSWAP W/ADC 28-SSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:119 系列:- 類型:熱交換控制器 應用:通用型，PCI Express? 內部開關:無 電流限制:- 電源電壓:3.3V，12V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:80-TQFP 供應商設備封裝:80-TQFP（12x12） 包裝:托盤 產品目錄頁面:1423 (CN2011-ZH PDF) |
| LTC4261CGN#PBF | 功能描述:IC CTRLR HOTSWAP W/ADC 28-SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:119 系列:- 類型:熱交換控制器 應用:通用型，PCI Express? 內部開關:無 電流限制:- 電源電壓:3.3V，12V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:80-TQFP 供應商設備封裝:80-TQFP（12x12） 包裝:托盤 產品目錄頁面:1423 (CN2011-ZH PDF) |
| LTC4261CGN#TR | 功能描述:IC CTRLR HOTSWAP W/ADC 28-SSOP RoHS:否 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:119 系列:- 類型:熱交換控制器 應用:通用型，PCI Express? 內部開關:無 電流限制:- 電源電壓:3.3V，12V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:80-TQFP 供應商設備封裝:80-TQFP（12x12） 包裝:托盤 產品目錄頁面:1423 (CN2011-ZH PDF) |
| LTC4261CGN#TRPBF | 功能描述:IC CTRLR HOTSWAP W/ADC 28-SSOP RoHS:是 類別:集成電路 (IC) >> PMIC - 熱交換 系列:- 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:119 系列:- 類型:熱交換控制器 應用:通用型，PCI Express? 內部開關:無 電流限制:- 電源電壓:3.3V，12V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:80-TQFP 供應商設備封裝:80-TQFP（12x12） 包裝:托盤 產品目錄頁面:1423 (CN2011-ZH PDF) |
發布緊急采購，3分鐘左右您將得到回復。