欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號： MB91FV130CR-ES
廠商： FUJITSU LTD
元件分類： 微控制器/微處理器
英文描述： 32-Bit RISC Microcontroller
中文描述： 32-BIT, 33 MHz, RISC MICROCONTROLLER, CPGA299
封裝： CERAMIC, PGA-299
文件頁數： 20/123頁
文件大小： 1362K
代理商： MB91FV130CR-ES
MB91133/MB91F133
20
I
HANDLING DEVICES
1.
Points to Note on Handling Devices
(1) Latch-up prevention
Latch-up may occur by CMOS IC if a voltage in excess of V
CC
5 or lower than V
SS
is applied to the input/output
pins, or if the voltage exceeds the rating between V
CC
5 and V
SS
. If latch-up occurs, the electrical current increases
significantly and may destroy certain components due to excessive heat, so great care must be taken to ensure
that the maximum rating is not exceeded during use.
(2) Handling Pins
Handling unused pins
Input pins that are not used should be pulled up or down as they may cause erroneous operations if left open.
Handling N.C. pins
N.C. pins must be opened for use.
Handling output pins
Excessive electric current may flow if the output pin is shorted by the power source or other output pins, or
connected to large loads. If such status is prolonged, the device is liable to be damaged, so great care must
be taken to ensure that the usage volume does not exceed the maximum rating.
Mode pins (MD0 to MD2)
Those pins must be directly connected to V
CC
5 or V
SS
for use.
Pattern lengths between V
CC
5 or V
SS
and each mode pin on the printed-circuit board should be arranged to
be as short as possible to prevent the test mode from being erroneously turned on due to noise, and they
should be connected with low impedance.
Power pins
When there are a number of V
CC
5/V
CC
3/V
SS
, those whose electrical potential must be the same within the
device are connected to prevent erroneous operation such as latch-up for device design purposes, but those
must be externally connected to a power source and earthed to follow the general output current standard and
prevent erroneous operation of strobe signals due to increased ground level and reduction in unnecessary
radiation.
Care must also be taken to ensure that they are connected to the V
CC
5/V
SS
or V
CC
3/V
SS
of this device at the
lowest possible impedance from the source of the electrical current supply.
Furthermore, it is recommended that a ceramic capacitor of around 0.1
μ
F be used to connect the V
CC
5 and
V
SS
, or V
CC
3 and V
SS
near the device as a bypass capacitor.
Crystal oscillation circuits
Noise near the X0, X1, X0A or X1A pins can cause erroneous operation. The printed-circuit board must be
designed so that the X0, X1, X0A and X1A pins, crystal oscillator (or ceramic oscillator) and bypass capacitor
to the ground can be arranged as close as possible.
Also, a printed-circuit board with grounded artwork enclosing the X0, X1, X0A and X1A pins is strongly
recommended to ensure stable operation.
相關PDF資料
PDF描述
MB91F133PBT 32-Bit RISC Microcontroller
MB91133PBT 32-Bit RISC Microcontroller
MB91F133PMT2 32-Bit RISC Microcontroller
MB91133 32-Bit RISC Microcontroller
MB91133PMT2 32-Bit RISC Microcontroller
相關代理商/技術參數
參數描述
MB91FV310A 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:Proprietary 32-bit Microcontroller CMOS
MB91FV310APFV-ES 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:Proprietary 32-bit Microcontroller CMOS
MB91FV319A 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit Microcontroller
MB91FV319APMT-ES 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit Microcontroller
MB91FV319R 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:32-bit Proprietary Microcontrollers
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*
主站蜘蛛池模板： 布拖县| 安丘市| 石城县| 阿合奇县| 永清县| 应用必备| 呼图壁县| 信宜市| 兴隆县| 岑巩县| 南京市| 大埔区| 仙居县| 合作市| 辽阳县| 巴东县| 隆子县| 河津市| 浙江省| 德安县| 邹城市| 普定县| 循化| 镇宁| 克拉玛依市| 新和县| 青海省| 晋宁县| 中江县| 松原市| 安陆市| 苏尼特右旗| 雷山县| 和林格尔县| 鲁山县| 青海省| 宁阳县| 启东市| 屏山县| 福州市| 彝良县|