- 您現在的位置：買賣IC網 > PDF目錄382301 > MC4GH01GNMCA-2SA00 (SAMSUNG SEMICONDUCTOR CO. LTD.) SAMSUNG MultiMediaCard PDF資料下載
參數資料
| 型號： | MC4GH01GNMCA-2SA00 |
| 廠商： | SAMSUNG SEMICONDUCTOR CO. LTD. |
| 英文描述： | SAMSUNG MultiMediaCard |
| 中文描述： | 三星多媒體 |
| 文件頁數： | 34/102頁 |
| 文件大小： | 1384K |
| 代理商： | MC4GH01GNMCA-2SA00 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁當前第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁
MultiMediaCard
TM
34
Sep.22.2005
Revision 0.3
S_CMD_SET
This field defines which command sets are supported by the card.
MIN_PERF_a_b_ff
These fields defines the overall minimum performance value for the read and write access with different bus width and
max clock frequency modes. The value in the register is coded as follows. Other than defined values are illegal.
Bit
Command Set
7-3
Reserved
2
Content Protection SecureMMC
1
SecureMMC
0
Standard MMC
Value
Performance
0x00
For Cards not reaching the 2.4MB/s minimum value
0x08
Class A: 2.4MB/s and is the lowest allowed value for MMCplus and MMCmobile(16x150kB/s)
0x0A
Class B: 3.0MB/s and is the next allowed value (20x150kB/s)
0x0F
Class C: 4.5MB/s and is the next allowed value (30x150kB/s)
0x14
Class D: 6.0MB/s and is the next allowed value (40x150kB/s)
0x1E
Class E: 9.0MB/s and is the next allowed value (60x150kB/s)
This is also the highest class which any MMCplus or MMCmobile card is needed to support in low bus
category operation mode (26MHz with 4bit data bus).
A MMCplus or MMCmobile card supporting any higher class than this have to support this class also
(in low category bus operation mode).
0x28
Class F: Equals 12.0MB/s and is the next allowed value (80x150kB/s)
0x32
Class G: Equals 15.0MB/s and is the next allowed value (100x150kB/s)
0x3C
Class H: Equals 18.0MB/s and is the next allowed value (120x150kB/s)
0x46
Class J: Equals 21.0MB/s and is the next allowed value (140x150kB/s)
This is also the highest class which any MMCplus or MMCmobile card is needed to support in mid bus
category operation mode (26MHz with 8bit data bus or 52MHz with 4bit data bus).
A MMCplus or MMCmobile card supporting any higher class than this have to support this Class (in
mid category bus operation mode) and Class E also (in low category bus operation mode)
0x50
Class K: Equals 24.0MB/s and is the next allowed value (160x150kB/s)
0x64
Class M: Equals 30.0MB/s and is the next allowed value (200x150kB/s)
0x78
Class O: Equals 36.0MB/s and is the next allowed value (240x150kB/s)
0x8C
Class R: Equals 42.0MB/s and is the next allowed value (280x150kB/s)
0xA0
Class T: Equals 48.0MB/s and is the last defined value (320x150kB/s)
Table 5-28 : R/W Access Performance Value
相關PDF資料 |
PDF描述 |
|---|---|
| MC4GH02GNMCA-2SA00 | SAMSUNG MultiMediaCard |
| MC206 | THIN SMD LOW/MEDIUM-FREQUENCY CRYSTAL UNIT |
| MC2300 | Navigator Motion Processor |
| MC26LS30 | Dual Differential Quad Single-Ended (EIA-423-A) Line Drivers |
| MC26LS30D | CABLE GLAND, PG29 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC4GH02GNMCA-2SA00 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:SAMSUNG MultiMediaCard |
| MC4M | 制造商:G & J HALL 功能描述:STEP DRILL MULTICUT 4-12MM X 2MM 制造商:G & J HALL 功能描述:STEP DRILL, MULTICUT, 4-12MM X 2MM |
| MC-4-MALE | 制造商:Multi-Contact USA 功能描述: |
| MC4MANUAL | 制造商:Omron Corporation 功能描述: |
| MC-4R128CEE6B | 制造商:NEC 制造商全稱:NEC 功能描述:Direct Rambus DRAM RIMM Module 128M-BYTE 64M-WORD x 16-BIT |
發布緊急采購，3分鐘左右您將得到回復。