- 您現在的位置：買賣IC網 > PDF目錄382301 > MC4GH01GNMCA-2SA00 (SAMSUNG SEMICONDUCTOR CO. LTD.) SAMSUNG MultiMediaCard PDF資料下載
參數資料
| 型號： | MC4GH01GNMCA-2SA00 |
| 廠商： | SAMSUNG SEMICONDUCTOR CO. LTD. |
| 英文描述： | SAMSUNG MultiMediaCard |
| 中文描述： | 三星多媒體 |
| 文件頁數： | 40/102頁 |
| 文件大小： | 1384K |
| 代理商： | MC4GH01GNMCA-2SA00 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁當前第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁
MultiMediaCard
TM
40
Sep.22.2005
Revision 0.3
Figure 6-1 : MultiMediaCard State Diagram (Card Identification Mode)
By omitting the voltage range in the command (by setting the argument of CMD1 to 0), the host can query the card and
determine the voltage type of the card. This bus query should be used if the host is able to select a common voltage
range, or if a notification to the application of a non usable card in the bus is desired. Afterwards, the host must choose a
voltage for operation, and reissue CMD1 with this condition, sending incompatible cards into the
Inactive State
.
The busy bit in the CMD1 response can be used by a card to tell the host that it is still working on its power-up/reset pro-
cedure (e.g. downloading the register information from memory field) and is not ready yet for communication. In this case
the host must repeat CMD1 until the busy bit is cleared.
During the initialization procedure, the host is not allowed to change the operating voltage range. Such changes shall be
ignored by the card. If there is a real change in the operating conditions, the host must reset the card (using CMD0) and
restart the initialization procedure. However, for accessing cards already in
Inactive State
, a hard reset must be done by
switching the power supply off and back on.
The command GO_INACTIVE_STATE (CMD15) can be used to send an addressed card into the
Inactive State
. This com-
mand is used when the host explicitly wants to deactivate a card (e.g. host is changing V
DD
into a range which is known to
be not supported by this card).
Ready State
(ready)
CMD1
Inactive
State (ina)
Idle State
(idle)
Identification
State (ident)
CMD0
CMD3
CMD2
from all states except (ina)
from all states in
data-transfer-mode
CMD15
card looses bus
card wins bus
cards with non compatible voltage range
card is busy or
host omitted voltage range
data-transfer mode
card-identification mode
Stand-by State
(stby)
Power on
CMD40
data-transfer mode
Interrupt mode
Wait-IRQ State
(irq)
Any start bit detected on the bus
相關PDF資料 |
PDF描述 |
|---|---|
| MC4GH02GNMCA-2SA00 | SAMSUNG MultiMediaCard |
| MC206 | THIN SMD LOW/MEDIUM-FREQUENCY CRYSTAL UNIT |
| MC2300 | Navigator Motion Processor |
| MC26LS30 | Dual Differential Quad Single-Ended (EIA-423-A) Line Drivers |
| MC26LS30D | CABLE GLAND, PG29 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC4GH02GNMCA-2SA00 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:SAMSUNG MultiMediaCard |
| MC4M | 制造商:G & J HALL 功能描述:STEP DRILL MULTICUT 4-12MM X 2MM 制造商:G & J HALL 功能描述:STEP DRILL, MULTICUT, 4-12MM X 2MM |
| MC-4-MALE | 制造商:Multi-Contact USA 功能描述: |
| MC4MANUAL | 制造商:Omron Corporation 功能描述: |
| MC-4R128CEE6B | 制造商:NEC 制造商全稱:NEC 功能描述:Direct Rambus DRAM RIMM Module 128M-BYTE 64M-WORD x 16-BIT |
發布緊急采購，3分鐘左右您將得到回復。