欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號： MC4GH01GNMCA-2SA00
廠商： SAMSUNG SEMICONDUCTOR CO. LTD.
英文描述： SAMSUNG MultiMediaCard
中文描述： 三星多媒體
文件頁數： 43/102頁
文件大小： 1384K
代理商： MC4GH01GNMCA-2SA00
MultiMediaCard
TM
43
Sep.22.2005
Revision 0.3
All data communication in the Data Transfer Mode is point-to point between the host and the selected card (using
addressed commands). All addressed commands get acknowledged by a response on the CMD line.
The relationship between the various data transfer modes is summarized below (see Figure 6-2):
All data read commands can be aborted any time by the stop command (CMD12). The data transfer will terminate and
the card will return to the
Transfer State.
The read commands are: block read (CMD17), multiple block read (CMD18)
and send write protect (CMD30).
All data write commands can be aborted any time by the stop command (CMD12). The write commands must be
stopped prior to deselecting the card by CMD7. The write commands are: block write (CMD24 and CMD25), write CID
(CMD26), and write CSD (CMD27).
As soon as the data transfer is completed, the card will exit the data write state and move either to the
Programming
State
(transfer is successful) or
Transfer State
(transfer failed).
If a block write operation is stopped and the block length and CRC of the last block are valid, the data will be pro
grammed.
The card may provide buffering for stream and block write. This means that the next block can be sent to the card while
the previous is being programmed.
If all write buffers are full, and as long as the card is in
Programming State
(see MultiMediaCard state diagram
Figure -2), the DAT0 line will be kept low.
There is no buffering option for write CSD, write CID, write protection and erase. This means that while the card is busy
servicing any one of these commands, no other data transfer commands will be accepted. DAT0 line will be kept low as
long as the card is busy and in the
Programming State
.
Parameter set commands are
not
allowed while card is programming.
Parameter set commands are: set block length (CMD16), and erase group selection (CMD35-36).
Read commands are
not
allowed while card is programming.
Moving another card from
Stand-by
to
Transfer State
(using CMD7) will not terminate a programming operation. The
card will switch to the
Disconnect State
and will release the DAT0 line.
A card can be reselected while in the
Disconnect State
, using CMD7. In this case the card will move to the
Program
ming State
and reactivate the busy indication.
Resetting a card (using CMD0 or CMD15) will terminate any pending or active programming operation. This may
destroy the data contents on the card. It is up to the host’s responsibility to prevent this.
Prior to executing the bus testing procedure (CMD19, CMD14), it is recommended to set up the clock frequency used
for data transfer. This way the bus test gives a true result, which might not be the case if the bus testing procedure is
performed with lower clock frequency than the data transfer frequency.
In the following format definitions, all upper case flags and parameters are defined in the CSD (Chapter 5.5.3), and the
other status flags in the Card Status (Chapter 6.9).
相關PDF資料
PDF描述
MC4GH02GNMCA-2SA00 SAMSUNG MultiMediaCard
MC206 THIN SMD LOW/MEDIUM-FREQUENCY CRYSTAL UNIT
MC2300 Navigator Motion Processor
MC26LS30 Dual Differential Quad Single-Ended (EIA-423-A) Line Drivers
MC26LS30D CABLE GLAND, PG29
相關代理商/技術參數
參數描述
MC4GH02GNMCA-2SA00 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:SAMSUNG MultiMediaCard
MC4M 制造商:G & J HALL 功能描述:STEP DRILL MULTICUT 4-12MM X 2MM 制造商:G & J HALL 功能描述:STEP DRILL, MULTICUT, 4-12MM X 2MM
MC-4-MALE 制造商:Multi-Contact USA 功能描述:
MC4MANUAL 制造商:Omron Corporation 功能描述:
MC-4R128CEE6B 制造商:NEC 制造商全稱:NEC 功能描述:Direct Rambus DRAM RIMM Module 128M-BYTE 64M-WORD x 16-BIT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*
主站蜘蛛池模板： 凤冈县| 阜平县| 乐业县| 阿城市| 芒康县| 青铜峡市| 文山县| 民权县| 黎川县| 凯里市| 灵寿县| 东海县| 辽阳市| 荣昌县| 南川市| 明星| 秭归县| 甘泉县| 建阳市| 宿松县| 墨竹工卡县| 广平县| 汉川市| 宿松县| 清涧县| 阿鲁科尔沁旗| 靖边县| 宜兰县| 甘德县| 清原| 宁海县| 蚌埠市| 克东县| 铜川市| 泌阳县| 康平县| 宁夏| 仙游县| 军事| 广饶县| 霍山县|