- 您現在的位置：買賣IC網 > PDF目錄382301 > MC4GH01GNMCA-2SA00 (SAMSUNG SEMICONDUCTOR CO. LTD.) SAMSUNG MultiMediaCard PDF資料下載
參數資料
| 型號： | MC4GH01GNMCA-2SA00 |
| 廠商： | SAMSUNG SEMICONDUCTOR CO. LTD. |
| 英文描述： | SAMSUNG MultiMediaCard |
| 中文描述： | 三星多媒體 |
| 文件頁數： | 69/102頁 |
| 文件大小： | 1384K |
| 代理商： | MC4GH01GNMCA-2SA00 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁當前第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁
MultiMediaCard
TM
69
Sep.22.2005
Revision 0.3
Bits
Identifier
Type
Det-
Mode
Value
Descript
Clear
Cond
31
ADDRESS_
OUT_OF_RANGE
E
R
’0’= no error
’1’= error
The command’s address argument was out
of the allowed range for this card.
C
X
A multiple block or stream read/write opera-
tion is (although started in a valid address)
attempting to read or write beyond the card
capacity
30
ADDRESS_MISALIG
N
E
R
’0’= no error
’1’= error
The command’ s address argument (in
accordance with the currently set block
length) positions the first data block mis-
aligned to the card physical blocks.
C
X
A multiple block read/write operation
(although started with a valid address/block-
length combination) is attempting to read or
write a data block which does not align with
the physical blocks of the card.
29
BLOCK_LEN_ERRO
R
E
R
’0’= no error
’1’= error
Either the argument of a SET_BLOCKLEN
command exceeds the maximum value
allowed for the card, or the previously
defined block length is illegal for the current
command (e.g. the host issues a write com-
mand, the current block length is smaller
than the card’s maximum and write partial
blocks is not allowed)
C
28
ERASE_SEQ_ERRO
R
E
R
’0’= no error
’1’= error
An error in the sequence of erase commands
occurred.
C
27
ERASE_PARAM
E
X
’0’= no error
’1’= error
An invalid selection of erase groups for erase
occurred.
C
26
WP_VIOLATION
E
X
’0’= no error
’1’= error
Attempt to program a write protected block.
C
25
CARD_IS_LOCKED
S
R
‘0’ = card unlocked
‘1’ = card locked
When set, signals that the card is locked by
the host
A
24
LOCK_UNLOCK_
FAILED
E
X
‘0’ = no error
‘1’ = error
Set when a sequence or password error has
been detected in lock/unlock card command
C
23
COM_CRC_ERROR
E
R
’0’= no error
’1’= error
The CRC check of the previous command
failed.
B
22
ILLEGAL_COMMAND E
R
’0’= no error
’1’= error
Command not legal for the card state
B
21
CARD_ECC_FAILED
E
X
’0’= success
’1’= failure
Card internal ECC was applied but failed to
correct the data.
C
20
CC_ERROR
E
R
’0’= no error
’1’= error
(Undefined by the standard)
A card error occurred, which is not related to
the host command.
C
Table 6-22 : Card Status
相關PDF資料 |
PDF描述 |
|---|---|
| MC4GH02GNMCA-2SA00 | SAMSUNG MultiMediaCard |
| MC206 | THIN SMD LOW/MEDIUM-FREQUENCY CRYSTAL UNIT |
| MC2300 | Navigator Motion Processor |
| MC26LS30 | Dual Differential Quad Single-Ended (EIA-423-A) Line Drivers |
| MC26LS30D | CABLE GLAND, PG29 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| MC4GH02GNMCA-2SA00 | 制造商:SAMSUNG 制造商全稱:Samsung semiconductor 功能描述:SAMSUNG MultiMediaCard |
| MC4M | 制造商:G & J HALL 功能描述:STEP DRILL MULTICUT 4-12MM X 2MM 制造商:G & J HALL 功能描述:STEP DRILL, MULTICUT, 4-12MM X 2MM |
| MC-4-MALE | 制造商:Multi-Contact USA 功能描述: |
| MC4MANUAL | 制造商:Omron Corporation 功能描述: |
| MC-4R128CEE6B | 制造商:NEC 制造商全稱:NEC 功能描述:Direct Rambus DRAM RIMM Module 128M-BYTE 64M-WORD x 16-BIT |
發布緊急采購，3分鐘左右您將得到回復。