欧美成人免费电影,国产欧美一区二区三区精品酒店,精品国产a毛片,色网在线免费观看

參數資料
型號: MC56F8346
廠商: Motorola, Inc.
英文描述: 56F8346 16-bit Hybrid Controller
中文描述: 56F8346 16位混合控制器
文件頁數: 36/160頁
文件大小: 1415K
代理商: MC56F8346
36
56F8346 Technical Data
Preliminary
4.3 Interrupt Vector Table
Table 4-5
provides the reset and interrupt priority structure, including on-chip peripherals. The
table is organized with higher-priority vectors at the top and lower-priority interrupts lower in the
table. The priority of an interrupt can be assigned to different levels, as indicated, allowing some
control over interrupt priorities. All level 3 interrupts will be serviced before level 2, and so on. For
a selected priority level, the lowest vector number has the highest priority.
The location of the vector table is determined by the Vector Base Address (VBA) register. Please
see
Section 5.6.12
for the reset value of the VBA.
In some configurations, the reset address and COP reset address will correspond to vector 0 and 1
of the interrupt vector table. In these instances, the first two locations in the vector table must
contain branch or JMP instructions. All other entries must contain JSR
instructions.
Table 4-4 Program Memory Map at Reset
Begin/End
Address
Mode 0 (MA = 0)
Mode 1
1
(MA = 1)
1.
If Flash Security Mode is enabled, EXTBOOT Mode 1 cannot be used. See
Security Features,
Part 7
.
Internal Boot
External Boot
Internal Boot
16-Bit External Address Bus
EMI_MODE = 0
2
,
3
16-Bit External Address Bus
2.
This mode provides maximum compatibility with 56F80x parts while operating externally.
3.
“EMI_MODE =0” when EMI_MODE pin is tied to ground at boot up.
EMI_MODE = 1
4
20-Bit External Address Bus
4.
“EMI_MODE =1” when EMI_MODE pin is tied to V
DD
at boot up.
Not accessible in reset configuration, since the address is above P:$00 FFFF. The higher bit address/GPIO (and/or chip
selects) pins must be reconfigured before this external memory is accessible.
P:$1F FFFF
P:$10 0000
External Program Memory
5
5.
External Program Memory
5
External Program Memory
5
P:$0F FFFF
P:$03 0000
External Program RAM
COP Reset Address = 02 0002
6
Boot Location = 02 0000
6
6.
Booting from this external address allows prototyping of the internal Boot Flash.
P:$02 FFFF
P:$02 F800
On-Chip Program RAM
4KB
P:$02 F7FF
P:$02 1000
Reserved
116KB
P:$02 0FFF
P:$02 0000
Boot Flash
8KB
COP Reset Address = 02 0002
Boot Location = 02 0000
Boot Flash
8KB
(Not Used for Boot in this Mode)
P:$01 FFFF
P:$01 0000
External Program RAM
5
Internal Program Flash
7
128KB
7.
The internal Program Flash is relocated in this mode making it accessible.
P:$00 FFFF
P:$00 0000
Internal Program Flash
128KB
External Program RAM
COP Reset Address = 00 0002
Boot Location = 00 0000
F
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
n
.
相關PDF資料
PDF描述
MC56F8346MFV60 56F8346 16-bit Hybrid Controller
MC56F8346VFV60 56F8346 16-bit Hybrid Controller
MC56F8356 56F8356 16-bit Hybrid Controller
MC56F8356VFV60 56F8356 16-bit Hybrid Controller
MC56F8356MFV60 56F8356 16-bit Hybrid Controller
相關代理商/技術參數
參數描述
MC56F8346EVM 制造商:Freescale Semiconductor 功能描述:Tools Development kit Kit Contents:Inst
MC56F8346MFV60 功能描述:數字信號處理器和控制器 - DSP, DSC 60MHz 60MIPS RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
MC56F8346MFVE 功能描述:數字信號處理器和控制器 - DSP, DSC 16 BIT HYBRID CONTROLLER RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
MC56F8346VFV60 功能描述:數字信號處理器和控制器 - DSP, DSC 60MHz 60MIPS RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
MC56F8346VFVE 功能描述:數字信號處理器和控制器 - DSP, DSC 16 BIT HYBRID CNTRLR RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
主站蜘蛛池模板: 岳池县| 静安区| 上蔡县| 英吉沙县| 改则县| 鄂尔多斯市| 德令哈市| 修文县| 濮阳县| 张北县| 简阳市| 莱州市| 阿拉善盟| 五大连池市| 连平县| 沽源县| 兴隆县| 盱眙县| 灵宝市| 杂多县| 丹东市| 黄骅市| 西充县| 项城市| 武强县| 尼勒克县| 天门市| 屏南县| 明溪县| 呼伦贝尔市| 青浦区| 永修县| 丰台区| 怀来县| 五指山市| 东台市| 宜川县| 理塘县| 建宁县| 丰原市| 丰顺县|